Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Home >>> SST >>> 49LF002 Datasheet

49LF002 Datasheet

Part Name
Description
MFG CO.
49LF002
SST
Silicon Storage Technology SST
Other PDF
  not available.
PDF
DOWNLOAD     
49LF002 image

PRODUCT DESCRIPTION
The SST49LF00xA flash memory devices are designed to be read-compatible with the Intel 82802 Firmware Hub (FWH) device for PC-BIOS application. It provides protection for the storage and update of code and data in addition to adding system design flexibility through five general purpose inputs. Two interface modes are sup ported by the SST49LF00xA: Firmware Hub (FWH)
Interface Mode for In-System programming and Parallel Programming (PP) Mode for fast factory programming of PC-BIOS applications.

FEATURES:
• Firmware Hub for Intel 8xx Chipsets
• 2 Mbit, 3 Mbit, 4 Mbit, or 8 Mbit SuperFlash memory array for code/data storage
– SST49LF002A: 256K x8 (2 Mbit)
– SST49LF003A: 384K x8 (3 Mbit)
– SST49LF004A: 512K x8 (4 Mbit)
– SST49LF008A: 1024K x8 (8 Mbit)
• Flexible Erase Capability
– Uniform 4 KByte Sectors
– Uniform 16 KByte overlay blocks for SST49LF002A
– Uniform 64 KByte overlay blocks for SST49LF003A/004A/008A
– Top Boot Block protection
- 16 KByte for SST49LF002A
- 64 KByte for SST49LF003A/004A/008A
– Chip-Erase for PP Mode Only
• Single 3.0-3.6V Read and Write Operations
• Superior Reliability
– Endurance:100,000 Cycles (typical)
– Greater than 100 years Data Retention
• Low Power Consumption
– Active Read Current: 6 mA (typical)
– Standby Current: 10 µA (typical)
• Fast Sector-Erase/Byte-Program Operation
– Sector-Erase Time: 18 ms (typical)
– Block-Erase Time: 18 ms (typical)
– Chip-Erase Time: 70 ms (typical)
– Byte-Program Time: 14 µs (typical)
– Chip Rewrite Time:
SST49LF002A: 4 seconds (typical)
SST49LF003A: 6 seconds (typical)
SST49LF004A: 8 seconds (typical)
SST49LF008A: 15 seconds (typical)
– Single-pulse Program or Erase
– Internal timing generation
• Two Operational Modes
– Firmware Hub Interface (FWH) Mode for in-system operation
– Parallel Programming (PP) Mode for fast production programming
• Firmware Hub Hardware Interface Mode
– 5-signal communication interface supporting byte Read and Write
– 33 MHz clock frequency operation
– WP# and TBL# pins provide hardware write protect for entire chip and/or top Boot Block
– Block Locking Register for all blocks
– Standard SDP Command Set
– Data# Polling and Toggle Bit for End-of-Write detection
– 5 GPI pins for system design flexibility
– 4 ID pins for multi-chip selection
• Parallel Programming (PP) Mode
– 11-pin multiplexed address and 8-pin data I/O interface
– Supports fast In-System or PROM programming for manufacturing
• CMOS and PCI I/O Compatibility
• Packages Available
– 32-lead PLCC
– 32-lead TSOP (8mm x 14mm)

Page Link's: 1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36 
 

Part Name
Description
PDF
MFG CO.
128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
STMicroelectronics
16-Mbit (1-Mbit x 16, 2-Mbit x 8) FlashFile™ MEMORY
Intel
16 Mbit(1 Mbit x 16, 2 Mbit x 8) 5V Single Voltage Flash Memory
Sharp Electronics
32-MBIT (2 MBIT X 16, 4 MBIT X 8) FlashFile™ MEMORY
Intel
16 Mbit(1 Mbit x 16, 2 Mbit x 8) Flash Memory
Sharp Electronics
1 Mbit / 2 Mbit / 4 Mbit Multi-Purpose Flash
Microchip Technology
4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory
STMicroelectronics
2 Mbit (256Kb x8, Boot Block) 3V Supply Firmware Hub Flash Memory
STMicroelectronics
2 Mbit (256Kb x8, Boot Block) 3V Supply Firmware Hub Flash Memory
STMicroelectronics
4 Mbit CMOS 3.3Volt-only Firmware Hub Flash Memory
AMIC Technology

Share Link: 

All Rights Reserved© datasheetq.com  [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]