Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Home >>> NXP >>> LPC1315FBD48 Datasheet

LPC1315FBD48 Datasheet

Part Name
Description
MFG CO.
Other PDF
  not available.
PDF
DOWNLOAD     
LPC1315FBD48 image

General description
The LPC1315/16/17/45/46/47 are ARM Cortex-M3 based microcontrollers for embedded
applications featuring a high level of integration and low power consumption. The ARM
Cortex-M3 is a next generation core that offers system enhancements such as enhanced
debug features and a higher level of support block integration.

Features and benefits
 System:
  ARM Cortex-M3 r2p1 processor, running at frequencies of up to 72 MHz.
  ARM Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC).
  Non Maskable Interrupt (NMI) input selectable from several input sources.
  System tick timer.
 Memory:
  Up to 64 kB on-chip flash program memory with a 256 byte page erase function.
  In-System Programming (ISP) and In-Application Programming (IAP) via on-chip bootloader software. Flash updates via USB supported.
  Up to 4 kB on-chip EEPROM data memory with on-chip API support.
  Up to 12 kB SRAM data memory.
  16 kB boot ROM with API support for USB API, power control, EEPROM, and flash IAP/ISP.
 Debug options:
  Standard JTAG test interface for BSDL.
  Serial Wire Debug.
  Support for ETM ARM Cortex-M3 debug time stamping.
 Digital peripherals:
  Up to 51 General Purpose I/O (GPIO) pins with configurablepull-up/pull-down resistors, repeater mode, input inverter, and pseudo open-drain mode. Eight pins support programmable glitch filter.
  Up to 8 GPIO pins can be selected as edge and level sensitive interrupt sources.
  Two GPIO grouped interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins.
  High-current source output driver (20 mA) on one pin (P0_7).
  High-current sink driver (20 mA) on true open-drain pins (P0_4 and P0_5).
  Four general purpose counter/timers with a total of up to 8 capture inputs and 13 match outputs.
  Programmable Windowed WatchDog Timer (WWDT) with a internal low-power WatchDog Oscillator (WDO).
  Repetitive Interrupt Timer (RI Timer).
 Analog peripherals:
  12-bit ADC with eight input channels and sampling rates of up to 500 kSamples/s. 
   Serial interfaces:
  USB 2.0 full-speed device controller (LPC1345/46/47) with on-chip ROM-based USB driver library.
  USART with fractional baud rate generation, internal FIFO, a full modem control handshake interface, and support for RS-485/9-bit mode and synchronous mode. USART supports an asynchronous smart card interface (ISO 7816-3).
  Two SSP controllers with FIFO and multi-protocol capabilities.
  I2C-bus interface supporting the full I2C-bus specification andFast-mode Plus with a data rate of up to 1 Mbit/s with multiple address recognition and monitor mode.
 Clock generation:
  Crystal Oscillator with an operating range of 1 MHz to 25 MHz (system oscillator) with failure detector.
  12 MHz high-frequency Internal RC oscillator (IRC) trimmed to 1 % accuracy over the entire voltage and temperature range. The IRC can optionally be used as a system clock.
  Internal low-power, low-frequency WatchDog Oscillator (WDO) with programmable frequency output.
  PLL allows CPU operation up to the maximum CPU rate with the system oscillator or the IRC as clock sources.
  A second, dedicated PLL is provided for USB (LPC1345/46/47).
  Clock output function with divider that can reflect the crystal oscillator, the main clock, the IRC, or the watchdog oscillator.
 Power control:
  Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down.
  Power profiles residing in boot ROM allow optimized performance and minimized power consumption for any given application through one simple function call.
  Processor wake-up from Deep-sleep and Power-down modes via reset, selectable GPIO pins, watchdog interrupt, or USB port activity.
  Processor wake-up from Deep power-down mode using one special function pin.
  Integrated PMU (Power Management Unit) to minimize power consumption during Sleep, Deep-sleep, Power-down, and Deep power-down modes.
  Power-On Reset (POR).
  Brownout detect with up to four separate thresholds for interrupt and forced reset.
 Unique device serial number for identification.
 Single 3.3 V power supply (2.0 V to 3.6 V).
 Temperature range 40 C to +85 C.
 Available as LQFP64, LQFP48, and HVQFN33 package.

 Applications
 Consumer
    peripherals  
    Handheld scanners
 Medical
 USB audio devices
 Industrial control

Page Link's: 1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38  39  40  41  42  43  44  45  46  47  48  49  50  51 
 

Part Name
Description
PDF
MFG CO.
32-bit ARM Cortex-M3 microcontroller; up to 512 kB flash and 64 kB SRAM with Ethernet, USB 2.0 Host/Device/OTG, CAN
Philips Electronics
32-bit ARM Cortex-M3 MCU; up to 512 kB flash and 64 kB SRAM with Ethernet, USB 2.0 Host/Device/OTG, CAN
Philips Electronics
LED LIGHT BARS
Kingbright
Single-chip 32-bit microcontrollers; 128 kB ISP/IAP Flash with 64 kB/32 kB/16 kB RAM
Philips Electronics
8-bit 80C51 5 V low power 16/32/64 kB Flash microcontroller with 1 kB RAM
Philips Electronics
Single-chip 16-bit/32-bit microcontrollers; 8 kB/16 kB/32 kB flash with ISP/IAP, fast ports and 10-bit ADC
Philips Electronics
Holtek 32-bit Microcontroller with ARM Cortex™-M3 Core
Holtek Semiconductor
Holtek 32-bit Microcontroller with ARM®Cortex™-M3 Core
Holtek Semiconductor
16/32-bit ARM microcontrollers; flashless with 64 kB, with 10-bit ADC and external memory interface
Philips Electronics
8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs
Philips Electronics

Share Link: 

All Rights Reserved© datasheetq.com  [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]