Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Home >>> ST-Microelectronics >>> M28W160BT100N1T Datasheet

M28W160BT100N1T Datasheet

Part NameDescriptionManufacturer
M28W160BT100N1T 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory ST-Microelectronics
STMicroelectronics ST-Microelectronics
Other PDF  not available.
PDF DOWNLOAD     
M28W160BT100N1T image

SUMMARY DESCRIPTION
The M28W160B is a 16 Mbit (1 Mbit x 16) non-volatile Flash memory that can be erased electrically at the block level and programmed in-system on a Word-by-Word basis. These operations can be performed using a single low voltage (2.7 to 3.6V) supply. VDDQ allows to drive the I/O pin down to 1.65V. An optional 12V VPP power supply is provided to speed up customer programming.
The device features an asymmetrical blocked architecture. The M28W160B has an array of 39 blocks: 8 Parameter Blocks of 4 KWord and 31 Main Blocks of 32 KWord. M28W160BT has the Parameter Blocks at the top of the memory address space while the M28W160BB locates the Parameter Blocks starting from the bottom. The memory maps are shown in Figure 6, Block Addresses.
Parameter blocks 0 and 1 can be protected from accidental programming or erasure. Each block can be erased separately. Erase can be suspended in order to perform either read or program in any other block and then resumed. Program can be suspended to read data in any other block and then resumed. Each block can be programmed and erased over 100,000 cycles.
Program and Erase commands are written to the Command Interface of the memory. An on-chip Program/Erase Controller takes care of the timings necessary for program and erase operations. The end of a program or erase operation can be detected and any error conditions identified. The command set required to control the memory is consistent with JEDEC standards.

FEATURES SUMMARY
■ SUPPLY VOLTAGE
   – VDD = 2.7V to 3.6V Core Power Supply
   – VDDQ= 1.65V to 3.6V for Input/Output
   – VPP = 12V for fast Program (optional)
■ ACCESS TIME: 70, 85, 90,100ns
■ PROGRAMMING TIME
   – 10µs typical
   – Double Word Programming Option
■ COMMON FLASH INTERFACE
   – 64 bit Security Code
■ MEMORY BLOCKS
   – Parameter Blocks (Top or Bottom location)
   – Main Blocks
■ BLOCK PROTECTION on TWO PARAMETER BLOCKS
   – WP for Block Protection
■ AUTOMATIC STAND-BY MODE
■ PROGRAM and ERASE SUSPEND
■ 100,000 PROGRAM/ERASE CYCLES per BLOCK
■ ELECTRONIC SIGNATURE
   – Manufacturer Code: 20h
   – Top Device Code, M28W160BT: 90h
   – Bottom Device Code, M28W160BB: 91h

Page Links : 1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38  39  40  41  42  43  44  45 
 

Other manufacturer searches related to M28W160BT100N1T

Part NameDescriptionPDFManufacturer
M36W432BG 32 Mbit (2Mb x16, Boot Block) Flash Memory and 4 Mbit (256Kb x16) SRAM, Multiple Memory Product View STMicroelectronics
AB28F400BX-T90 4-MBIT (256K x16, 512K x8) BOOT BLOCK FLASH MEMORY FAMILY View Intel
M28R400CB 4 Mbit (256Kb x16, Boot Block) 1.8V Supply Flash Memory View STMicroelectronics
M29DW323DB 32 Mbit (4Mb x8 or 2Mb x16, Dual Bank 8:24, Boot Block) 3V Supply Flash Memory View Numonyx -> Micron
M29W320EB 32Mbit (4Mbx8 or 2Mbx16, Uniform Parameter Blocks, Boot Block) 3V supply Flash memory View Numonyx -> Micron
M29DW324DB 32 Mbit (4Mb x8 or 2Mb x16, Dual Bank 16:16, Boot Block) 3V Supply Flash Memory View Numonyx -> Micron
28F160B3 SMART 3 ADVANCED BOOT BLOCK WORD-WIDE 4-MBIT (256K X 16), 8-MBIT (512K X 16), 16-MBIT (1024K X 16) FLASH MEMORY FAMILY View Intel
28F160B3 SMART 3 ADVANCED BOOT BLOCK WORD-WIDE 4-MBIT (256K X 16), 8-MBIT (512K X 16), 16-MBIT (1024K X 16) FLASH MEMORY FAMILY View Intel
A28F200BX-B 2-MBIT (128K x 16, 256K x 8) BOOT BLOCK FLASH MEMORY FAMILY View Intel
M36DR432-ZAT 32 Mbit (2Mb x16, Dual Bank, Page) Flash Memory and 4 Mbit (256K x16) SRAM, Multiple Memory Product View STMicroelectronics

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]