Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Description + Content Search

Search Word's :
ETC
Unspecified
Description : Quartz CRYSTAL 18.432000 MHz

[SIWARD CRYSTAL TECHNOLOGY CO., LTD.]

CRYSTAL SPECIFICATION

1. Description : Quartz CRYSTAL
2. Nominal Frequency : 18.432000 MHz
3. Center Frequency : 18.432000 MHz
4. Dimension & Drawing No. : SX-3225 ; SXD-00213
5. Oscillation Mode : Fundamental
6. Cutting Mode : AT cut
7. Packing Style : TP-094
8. Measurement Instrument : S&A 250B(Measured FL)

Description : 18/20-Pin 8-Bit CMOS Microcontroller with UHF ASK/FSK Transmitter

GENERAL DESCRIPTION
The rfPIC12C509AG/509AF from Microchip TECHNOLOGY is a low-cost, high performance, 8-bit, fully static, EPROM-based CMOS microcontroller combined with a UHF ASK/FSK transmitter. It employs a RISC architecture with only 33 single word/single cycle instructions. All instructions are single cycle (1 µs) except for program branches which take two cycles. The 12-bit wide instructions are highly symmetrical resulting in 2:1 code compression over other 8-bit microcontrollers in its class. The easy to use and easy to remember instruction set reduces development time significantly.

High-Performance RISC CPU:
• Only 33 single word instructions to learn
• All instructions are single cycle (1 µs) except for program branches which are two-cycle
• Operating speed: DC - 4 MHz clock input DC - 1 µs instruction cycle
• 12-bit wide instructions
• 8-bit wide data path
• Seven special function hardware registers
• Two-level deep hardware stack
• Direct, indirect and relative addressing modes for data and instructions
• Internal 4 MHz RC oscillator with programmable calibration (independent from transmitter quartz CRYSTAL reference)
• In-Circuit Serial Programming™ (ICSP™)

Peripheral Features:
• 8-bit real time clock/counter (TMR0) with 8-bit programmable prescaler
• Power-On Reset (POR)
• Device Reset Timer (DRT)
• Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation
• Programmable code-protection
• Power saving SLEEP mode
• Wake-up from SLEEP on pin change
• Internal weak pull-ups on I/O pins
• Internal pull-up on MCLR pin
• Selectable oscillator options:
    - INTRC: Internal 4 MHz RC oscillator
    - EXTRC: External low-cost RC oscillator
    - XT: Standard CRYSTAL/resonator
    - LP: Power saving, low frequency CRYSTAL

UHF ASK/FSK Transmitter:
• Conforms to US FCC Part 15.231 regulations and European ERC 70-03E and EN 300 220-1 requirements
• VCO phase locked to quartz CRYSTAL reference; allows narrow band receivers to be used to maximize range and interference immunity
• Integrated CRYSTAL oscillator and VCO requiring minimum of external components
CRYSTAL frequency divide by 4 available (CLKOUT)
• Frequency range set by CRYSTAL: 310 – 480 MHz
• ASK Data rate: 0 – 40 Kbps
• FSK through CRYSTAL pulling allows modulation at 0 – 20 Kbps
• Adjustable output power: +2 dBm to -12 dBm in six discrete steps
• Differential output configurable for single or double ended loop antenna
• Power amplifier automatically disabled until after PLL lock

CMOS TECHNOLOGY:
• Low power, high speed CMOS EPROM TECHNOLOGY
• Fully static design
• Wide operating voltage range
• Wide temperature range:
    - Industrial: -40°C to +85°C
• PICmicro® MCU power consumption:
    - < 2 mA @ 5V, 4 MHz
    - 15 µA typical @ 3V, 32 KHz
    - < 1 µA typical standby current
• Transmitter power consumption: (depending on power selection)
    - 4.8 mA to 11.5 mA @ 3V
    - <1 µA typical standby current

Description : Dot Matrix Liquid CRYSTAL Display Controller/Driver

Description
The HD44780U dot-matrix liquid CRYSTAL display controller and driver LSI displays alphanumerics, Japanese kana characters, and symbols. It can be configured to drive a dot-matrix liquid CRYSTAL display under the control of a 4- or 8-bit microprocessor. Since all the functions such as display RAM, character generator, and liquid CRYSTAL driver, required for driving a dot-matrix liquid CRYSTAL display are internally provided on one chip, a minimal system can be interfaced with this controller/driver.
A single HD44780U can display up to one 8-character line or two 8-character lines.
The HD44780U has pin function compatibility with the HD44780S which allows the user to easily replace an LCD-II with an HD44780U. The HD44780U character generator ROM is extended to generate 208 5 × 8 dot character fonts and 32 5 × 10 dot character fonts for a total of 240 different character fonts.
The low power supply (2.7V to 5.5V) of the HD44780U is suitable for any portable battery-driven product requiring low power dissipation.

Features
• 5 × 8 and 5 × 10 dot matrix possible
• Low power operation support:
   - 2.7 to 5.5V
• Wide range of liquid CRYSTAL display driver power
   - 3.0 to 11V
• Liquid CRYSTAL drive waveform
   - A (One line frequency AC waveform)
• Correspond to high speed MPU bus interface
   - 2 MHz (when VCC = 5V)
• 4-bit or 8-bit MPU interface enabled
• 80 × 8-bit display RAM (80 characters max.)
• 9,920-bit character generator ROM for a total of 240 character fonts
   - 208 character fonts (5 × 8 dot)
   - 32 character fonts (5 × 10 dot)
• 64 × 8-bit character generator RAM
   - 8 character fonts (5 × 8 dot)
   - 4 character fonts (5 × 10 dot)
• 16-common × 40-segment liquid CRYSTAL display driver
• Programmable duty cycles
   - 1/8 for one line of 5 × 8 dots with cursor
   - 1/11 for one line of 5 × 10 dots with cursor
   - 1/16 for two lines of 5 × 8 dots with cursor
• Wide range of instruction functions:
   - Display clear, cursor home, display on/off, cursor on/off,
      display character blink, cursor shift, display shift
• Pin function compatibility with HD44780S
• Automatic reset circuit that initializes the controller/driver after power on
• Internal oscillator with external resistors
• Low power consumption

Hitachi
Hitachi -> Renesas Electronics
Description : Dot Matrix Liquid CRYSTAL Display Controller/Driver

Description
The HD66710 dot-matrix liquid CRYSTAL display controller and driver LSI displays alphanumerics, numbers, and symbols. It can be configured to drive a dot-matrix liquid CRYSTAL display under the control of a 4- or 8-bit microprocessor. Since all the functions such as display RAM, character generator, and liquid CRYSTAL driver, required for driving a dot-matrix liquid CRYSTAL display are internally provided on one chip, a minimum system can be interfaced with this controller/driver.

Features
• 5 × 8 dot matrix possible
• Low power operation support:
    - 2.7V to 5.5V (low voltage)
• Booster for liquid CRYSTAL voltage
    - Two/three times (13V max.)
• Wide range of liquid CRYSTAL display driver voltage
    - 3.0V to 13V
• Extension driver interface
• High-speed MPU bus interface (2 MHz at 5-V operation)
• 4-bit or 8-bit MPU interface capability
• 80 × 8-bit display RAM (80 characters max.)
• 9,600-bit character generator ROM
    - 240 characters (5 × 8 dot)
• 64 × 8-bit character generator RAM
    - 8 characters (5 × 8 dot)
• 8 × 8-bit segment RAM
    - 40-segment icon mark
• 33-common × 40-segment liquid CRYSTAL display driver
• Programmable duty cycle (See List 1)
• Wide range of instruction functions:
    - Functions compatible with LCD-II: Display clear, cursor home, display on/off, cursor on/off, display character blink, cursor shift, display shift
    - Additional functions: Icon mark control, 4-line display, horizontal smooth scroll, 6-dot character width control, white-black inverting blinking cursor
• Software upwardly compatible with HD44780
• Automatic reset circuit that initializes the controller/driver after power on
• Internal oscillator with an external resistor
• Low power consumption
• QFP1420-100 pin, TQFP1414-100 pin bare-chip

Description : Dot-Matrix Liquid CRYSTAL Display Controller/Driver

Description
The HD66712 dot-matrix liquid CRYSTAL display controller and driver LSI displays alphanumerics, numbers, and symbols. It can be configured to drive a dot-matrix liquid CRYSTAL display under the control of a serial or a 4- or 8-bit microprocessor. Since all the functions such as display RAM, character generator, and liquid CRYSTAL driver, required for driving a dot-matrix liquid CRYSTAL display are internally provided on one chip, a minimum system can be interfaced with this controller/driver.

Features
• 5 × 8 dot matrix possible
• Clock-synchronized serial interface capability; can interface with 4- or 8-bit MPU
• Low-power operation support:
    - 2.7 to 5.5V (low voltage)
    - Wide liquid-CRYSTAL voltage range: 2.7 to 11.0V max.
• Booster for liquid CRYSTAL voltage
    - Two/three times (13V max.)
• High-speed MPU bus interface (2MHz at 5-V operation)
• Extension driver interface
• Character display and independent 60-icon mark display possible
• Horizontal smooth scroll by 6-dot font width display possible
• 80 × 8-bit display RAM (80 characters max.)
• 9,600-bit character generator ROM
    - 240 characters (5 × 8 dot)
• 64 × 8-bit character generator RAM
    - 8 characters (5 × 8 dot)
• 16 × 8-bit segment icon mark
    - 96-segment icon mark
• 34-common × 60-segment liquid CRYSTAL display driver
• Programmable duty cycle (See List 1)
• Software upwardly compatible with HD44780
• Wide range of instruction functions:
    - Functions compatible with LCD-II: Display clear, cursor home, display on/off, cursor on/off, display character blink, cursor shift, display shift
    - Additional functions: Icon mark control, 4-line display, horizontal smooth scroll, 6-dot character width control, white-black inverting blinking cursor
• Automatic reset circuit that initializes the controller/driver after power on (standard version only)
• Internal oscillator with an external resistor
• Low power consumption
• TCP-128 pin, bare-chip

ICST
Integrated Circuit Systems
Description : CRYSTAL-TO-3.3V LVPECL FREQUENCY SYNTHESIZER W/INTEGRATED FANOUT BUFFER

GENERAL DESCRIPTION
The ICS84327 is a CRYSTAL-to-3.3V LVPECL Clock Synthesizer/Fanout Buffer designed for SONET, 10 Gigabit Fibre Channel and 10 Gigabit Ethernet applications and is a member of the HiperClockS family of High Performance Clock Solutions from ICS. The output frequency can be set using the frequency select pins and a 19.44MHz CRYSTAL for SONET frequencies, or a 25MHz CRYSTAL for 10 Gigabit Ethernet frequencies, or a 25.5MHz CRYSTAL for a 10 Gigabit Fibre Channel. The low phase noise characteristics of the ICS84327 make it an ideal clock for these demanding applications.

FEATURES
• 6 LVPECL outputs
CRYSTAL oscillator interface
• Output frequency range: 77.76MHz to 625MHz
CRYSTAL input frequency: 19.44MHz, 25MHz or 25.5MHz
• RMS phase jitter at 155.52MHz, using a 19.44MHz CRYSTAL (12KHz to 20MHz): 3.4ps (typical)
    Phase noise:
     Offset                     Noise Power
       100Hz .................. -92 dBc/Hz
        1KHz ................ -105 dBc/Hz
      10KHz ................ -122 dBc/Hz
    100KHz ................ -123 dBc/Hz
• Full 3.3V or 3.3V core, 2.5V output supply mode
• 0°C to 70°C ambient operating temperature
• Industrial temperature information available upon request

Description : CRYSTAL Oscillator Module ICs

OVERVIEW

The SM5009 series are CRYSTAL oscillator module ICs that incorporate low CRYSTAL current type oscillating circuit to limit oscillator-stage current, so that they can reduce CRYSTAL current lower than the existing products. Since the oscillating circuit has oscillator capacitors with excellent frequency response and feedback resistor built-in, just connecting CRYSTAL realizes stable fundamental oscillation responding up to 40MHz. The SM5009 series are ideal for SMD type CRYSTAL oscillator using a strip-shaped CRYSTAL blank.



FEATURES

■ Low CRYSTAL current oscillator

■ Up to 40MHz operating frequency range (funda mental oscillation)

■ Operating supply voltage range

   • 3V operation: 2.7 to 3.6V

   • 5V operation: 4.5 to 5.5V

■ –40 to 85°C operating temperature range

■ Oscillation capacitors CG, CD built-in

■ Inverter amplifier feedback resistor built-in

■ Standby function

   • Oscillator stops (AL series), high impedance in standby mode

■ Low standby current

   • Power-save pull-up resistor built-in (AL series)

■ Frequency divider built-in (fO, fO/2, fO/4, fO/8, fO/16, fO/32 determined by internal connection)

■ Output drive capability

   • AL×, AN×, AK×, CN×: 16mA (VDD = 4.5V)

   • AH×: 4mA (VDD = 4.5V)

■ Output load: CL = 50pF max.

■ Output duty level

   • CMOS level (1/2 VDD): AL×, AN×, AH×, CN×

   • TTL level (1.4V): AK×

■ Molybdenum-gate CMOS process

■ 8-pin SOP (SM5009×××S)

■ Chip form (CF5009×××)



 


IDT
Integrated Device Technology
Description : FEMTOCLOCKS™ CRYSTAL-TO-LVDS FREQUENCY SYNTHESIZER W/INTEGRATED FANOUT BUFFER

GENERAL DESCRIPTION
The ICS844256 is a CRYSTAL-to-LVDS Clock Synthesizer/Fanout Buffer designed for SONET and Gigabit Ethernet applications and is a member of the HiperClockS™ family of High Performance Clock Solutions from IDT. The output frequency can be set using the frequency select pins and a 25MHz CRYSTAL for Ethernet frequencies, or a 19.44MHz CRYSTAL for SONET. The low phase noise characteristics of the ICS844256 make it an ideal clock for these demanding applications.

FEATURES
• Six LVDS outputs
CRYSTAL oscillator interface
• Output frequency range: 62.5MHz to 622.08MHz
CRYSTAL input frequency range: 15.625MHz to 25.5MHz
• RMS phase jitter at 125MHz, using a 25MHz CRYSTAL (1.875MHz to 20MHz): 0.48ps (typical)
• Full 3.3V or 3.3V core, 2.5V output supply mode
• 0°C to 70°C ambient operating temperature
• Available in both standard (RoHS 5) and lead-free (RoHS 6) packages

IDT
Integrated Device Technology
Description : FemtoClock® CRYSTAL-to-LVDS Frequency Synthesizer w/Integrated Fanout Buffer

General Description
The ICS844256D is a CRYSTAL-to-LVDS Clock Synthesizer/Fanout Buffer designed for SONET and Gigabit Ethernet applications. The output frequency can be set using the frequency select pins and a 25MHz CRYSTAL for Ethernet frequencies, or a 19.44MHz CRYSTAL for SONET. The low phase noise characteristics of the ICS844256D make it an ideal clock for these demanding applications.

Features
• Six differential LVDS output pairs
CRYSTAL oscillator interface
• Output frequency range: 62.5MHz - 625MHz
CRYSTAL input frequency range:15.625MHz - 25.5MHz
• RMS phase jitter @ 125MHz, using a 25MHz CRYSTAL (1.875MHz – 20MHz): 0.43ps (typical)
• Full 3.3V or mixed 3.3V core, 2.5V output supply mode
• 0°C to 70°C ambient operating temperature
• Available in lead-free (RoHS 6) package

Hitachi
Hitachi -> Renesas Electronics
Description : Dot Matrix Liquid CRYSTAL GraphicDisplay Column Driver

Description
HD61202U is a column (segment) driver for dot matrix liquid CRYSTAL graphic display systems. It stores the display data transferred from a 8-bit micro controller in the internal display RAM and generates dot matrix liquid CRYSTAL driving signals.

Features
• Dot matrix liquid CRYSTAL graphic display column driver incorporating display RAM
• RAM data direct display by internal display RAM
    - RAM bit data 1: On
    - RAM bit data 0: Off
• Internal display RAM address counter preset, increment
• Display RAM capacity: 512 bytes (4096 bits)
• 8-bit parallel interface
• Internal liquid CRYSTAL display driver circuit: 64
• Display duty cycle
    Drives liquid CRYSTAL panels with 1/32–1/64 duty cycle multiplexing
• Wide range of instruction function
    Display data read/write, display on/off, set address, set display start line, read status
• Lower power dissipation: during display 2 mW max
• Power supply: VCC: 2.7V~5.5V
• Liquid CRYSTAL display driving voltage: 8V to 16V
• CMOS process

12345678910 Next



All Rights Reserved© datasheetq.com  [Privacy Policy ] [ Request Datasheet] [Contact Us]