Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Part name(s)'  

P/N + Description + Content Search

Search Word's :

Part name(s)' : 74ALVC162834A 74ALVC162834ADGG
Description : 18-bit registered driver with inverted register enable and 30 Ω termination resistors; 3-State
NXP
NXP Semiconductors.

General description
The 74ALVC162834A is an 18-bit registered driver.
   
Features and benefits
• Wide supply voltage range from 1.2 V to 3.6 V
• CMOS low-power consumption
• Direct interface with TTL levels (2.7 V to 3.6 V)
• Current drive ± 12 mA at 3.0 V
• MULTIBYTE flow-through standard pin-out architecture
• Low inductance multiple VCC and GND pins for minimum noise and ground bounce
• Output drive capability 50 Ω transmission lines at 85°C
• Integrated 30 Ω termination resistors
• Diode clamps to VCC and GND on all inputs
• Input diodes to accommodate strong drivers
• Complies with JEDEC standard no. 8-1A
   

View
Part name(s)' : 74ALVC162834A 74ALVC162834ADGG AC162834ADGG
Description : 18-bit registered driver with inverted register enable and 30Ω termination resistors (3-State)
Philips
Philips Electronics

DESCRIPTION
The 74ALVC162834A is an 18-bit registered driver.
   
FEATURES
• Wide supply voltage range of 1.2 V to 3.6 V
• Complies with JEDEC standard no. 8-1A.
• CMOS low power consumption
• Direct interface with TTL levels
• Current drive ± 12 mA at 3.0 V
• MULTIBYTETM flow-through standard pin-out architecture
• Low inductance multiple VCC and GND pins for minimum noise
    and ground bounce
• Output drive capability 50 Ω transmission lines @ 85°C
• Integrated 30 Ω termination resistors
• Diode clamps to VCC and GND on all inputs
• Input diodes to accommodate strong drivers
   

View
Part name(s)' : 74AVCM162835 74AVCM162835DGG
Description : 18-bit registered driver with 15 Ω termination resistors (3-State)
Philips
Philips Electronics

DESCRIPTION
The 74AVCM162835 is a 18-bit universal bus driver. Data flow is controlled by output enable (OE), latch enable (LE) and clock inputs (CP).

FEATURES
• Wide supply voltage range of 1.2 V to 3.6 V
• Complies with JEDEC standard no. 8-1A/5/7.
• CMOS low power consumption
• Input/output tolerant up to 3.6 V
• Low inductance multiple VCC and GND pins for minimum noise and ground bounce
• Integrated 15 Ω termination resistors to minimize output overshoot and undershoot
• Full PC133 solution provided when used with PCK2510S and CBT16292

View
Part name(s)' : 74AVCM162834 74AVCM162834DGG
Description : 18-bit registered driver with inverted register enable and 15 Ω termination resistors (3-State)
Philips
Philips Electronics

DESCRIPTION
The 74AVCM162834 is an 18-bit universal bus driver. Data flow is controlled by output enable (OE), latch enable (LE) and clock inputs (CP).
This product is designed to have an extremely fast propagation delay and a minimum amount of power consumption.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor (Live Insertion).

FEATURES
• Wide supply voltage range of 1.2 V to 3.6 V
• Complies with JEDEC standard no. 8-1A/5/7.
• CMOS low power consumption
• Input/output tolerant up to 3.6 V
• Low inductance multiple VCC and GND pins for minimum noise and ground bounce
• Integrated 15 Ω termination resistors to minimize output overshoot and undershoot
• Full PC133 solution provided when used with PCK2510S and CBT16292

View

Part name(s)' : 74ALVC162334A 74ALVC162334ADGG
Description : 16-bit registered driver with inverted register enable and 30Ω termination resistors (3-State)
Philips
Philips Electronics

DESCRIPTION
The 74ALVC162334A is an 16-bit universal bus driver.
   
FEATURES
• Wide supply voltage range of 1.2 V to 3.6 V
• Complies with JEDEC standard no. 8-1A.
• CMOS low power consumption
• Direct interface with TTL levels
• Current drive ± 24 mA at 3.0 V
• MULTIBYTETM flow-through standard pin-out architecture
• Low inductance multiple VCC and GND pins for minimum noise
    and ground bounce
• Output drive capability 50 Ω transmission lines @ 85°C
• Current drive ±24 mA at 3.0 V
• Integrated 30 Ω termination resistors
• Input diodes to accommodate strong drivers
   

View
Part name(s)' : 74ALVC162334A 74ALVC162334ADGG 74ALVC162334ADGG5 74ALVC162334ADGG,5 74ALVC162334ADGG1 74ALVC162334ADGG,1
Description : 16-bit registered driver with inverted register enable and 30 Ω termination resistors (3-State)
NXP
NXP Semiconductors.

General description
The 74ALVC162334A is a 16-bit universal bus driver.
   
Features
■ Wide supply voltage range of 1.2 V to 3.6 V
■ Complies with JEDEC standard 8-1A
■ CMOS low power consumption
■ Direct interface with TTL levels
■ Current drive: ±24 mA at 3.0 V
■ MULTIBYTE flow-through standard pinout architecture
■ Low inductance multiple VCC and GND pins
    for minimum noise and ground bounce
■ Output drive capability 50 Ω transmission lines at 85 °C
■ Integrated 30 Ω termination resistors
■ Input diodes to accommodate strong drivers
   

View
Part name(s)' : 74ALVT162823DGG 74ALVT162823
Description : 18-bit bus-interface D-type flip-flop with reset and enable with 30 Ω termination resistors; 3-State
NXP
NXP Semiconductors.

General description
The 74ALVT162823 18-bit bus interface register is designed to eliminate the extra packages required to buffer existing registers and provide extra data width for wider data or address paths of buses carrying parity.
   
Features and benefits
• Two sets of high speed parallel registers with positive
    edge-triggered D-type flip-flops
• 5 V I/O compatible
• Ideal where high speed, light loading or increased
    fan-in are required with MOS microprocessors
• Bus hold data inputs eliminate the need for external
    pull-up resistors to hold unused inputs
• Live insertion and extraction permitted
• Power-up 3-State
• Power-up reset
• Output capability: +12 mA to −12 mA
• Outputs include series resistance of 30 Ω making external
    termination resistors unnecessary
• Latch-up protection:
    – JESD78: exceeds 500 mA
• ESD protection:
    – MIL STD 883, method 3015: exceeds 2000 V
    – MM: exceeds 200 V
   

View
Part name(s)' : 74ALVT162823 74ALVT162823DGG 74ALVT162823DL AV162823DL AV162823DGG
Description : 18-bit bus-interface D-type flip-flop with reset and enable with 30Ω termination resistors (3-State)
Philips
Philips Electronics

DESCRIPTION
The 74ALVT162823 18-bit bus interface register is designed to eliminate the extra packages required to buffer existing registers and provide extra data width for wider data/address paths of buses carrying parity.
   
FEATURES
• Two sets of high speed parallel registers with positive
    edge-triggered D-type flip-flops
• 5V I/O Compatible
• Ideal where high speed, light loading, or increased fan-in are
    required with MOS microprocessors
• Live insertion/extraction permitted
• Power-up 3-State
• Power-up Reset
• Output capability: +12mA/–12mA
• Latch-up protection exceeds 500mA per Jedec Std 17
• ESD protection exceeds 2000 V per MIL STD 883 Method 3015
    and 200 V per Machine Model
• Bus hold data inputs eliminate the need for external pull-up
    resistors to hold unused inputs
• Outputs include series resistance of 30Ω making external
    termination resistors unnecessary
   

View
Part name(s)' : 74ALVC16834ADGG 74ALVC16834A
Description : 18-bit registered driver with inverted register enable (3-State)
Philips
Philips Electronics

DESCRIPTION
The 74ALVC16834A is an 18-bit registered driver.
   
FEATURES
• Wide supply voltage range of 1.2 V to 3.6 V
• Complies with JEDEC standard no. 8-1A.
• CMOS low power consumption
• Direct interface with TTL levels
• Current drive ± 24 mA at 3.0 V
• MULTIBYTETM flow-through standard pin-out architecture
• Low inductance multiple VCC and GND pins for minimum noise
    and ground bounce
• Output drive capability 50 Ω transmission lines @ 85°C
• Input diodes to accommodate strong drivers
   

View
12345678910 Next



All Rights Reserved© datasheetq.com 2015 - 2019  [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]