Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Description + Content Search

Search Word's :
Description : SOLID STATE RELAY (I/O Module) MAXIMUM LOAD CURRENT 1 A

■ FEATURES
● I/O modules for interface between CPU and external input devices or loads
● Ultra slim and light weight, SIL terminals type I/O modules for high density mounTing
    —Size: 5 (W) × 20 (L) × 17 (H) mm
    —Weight: approximately 3.0 to 3.5 g
● High isolation by employing photo-coupled devices (between input and output: 2,500 V rms)
● Long life and maintenance free
● All solid state I/O module
● Compatible with NY relay size and terminals arrangement (only output module type)

Description : 8-Pin, 8-Bit CMOS Microcontrollers

GENERAL DESCRIPTION
The PIC12C5XX from Microchip Technology is a family of low-cost, high performance, 8-bit, fully static, EEPROM/EPROM/ROM-based CMOS microcontrollers. It employs a RISC architecture with only 33 single word/single cycle instructions. All instructions are single cycle (1 µs) except for program branches which take two cycles. The PIC12C5XX delivers performance an order of magnitude higher than its competitors in the same price category. The 12-bit wide instructions are highly symmetrical resulTing in 2:1 code compression over other 8-bit microcontrollers in its class. The easy to use and easy to remember instruction set reduces development time significantly.

High-Performance RISC CPU:
• Only 33 single word instructions to learn
• All instructions are single cycle (1 µs) except for program branches which are two-cycle
• OperaTing speed: DC - 4 MHz clock input DC - 1 µs instruction cycle
• 12-bit wide instructions
• 8-bit wide data path
• Seven special function hardware registers
• Two-level deep hardware stack
• Direct, indirect and relative addressing modes for data and instructions
• Internal 4 MHz RC oscillator with programmable calibration
• In-circuit serial programming

Peripheral Features:
• 8-bit real time clock/counter (TMR0) with 8-bit programmable prescaler
• Power-On Reset (POR)
• Device Reset Timer (DRT)
• Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation
• Programmable code-protection
• 1,000,000 erase/write cycle EEPROM data memory
• EEPROM data retention > 40 years
• Power saving SLEEP mode
• Wake-up from SLEEP on pin change
• Internal weak pull-ups on I/O pins
• Internal pull-up on MCLR pin
• Selectable oscillator options:
   - INTRC: Internal 4 MHz RC oscillator
   - EXTRC: External low-cost RC oscillator
   - XT: Standard crystal/resonator
   - LP: Power saving, low frequency crystal

CMOS Technology:
• Low power, high speed CMOS EPROM/ROM technology
• Fully static design
• Wide operaTing voltage range
• Wide temperature range:
   - Commercial: 0°C to +70°C
   - Industrial: -40°C to +85°C
   - Extended: -40°C to +125°C
• Low power consumption
   - < 2 mA @ 5V, 4 MHz
   - 15 µA typical @ 3V, 32 KHz
   - < 1 µA typical standby current

Description : Microcontroller Supervisory Circuit with Open Drain Output

DESCRIPTION
The Microchip Technology Inc. MCP120/130 is a voltage supervisory device designed to keep a microcontroller in reset until the system voltage has reached the proper level and stabilized.
It also operates as protection from brown-out conditions when the supply voltage drops below a safe operaTing level. Both devices are available with a choice of seven different trip voltages and both have open drain outputs.

FEATURES
• Holds microcontroller in reset until supply voltage
reaches stable operaTing level
• Resets microcontroller during power loss
• Precision monitoring of 3V, 3.3V and 5V systems
• 7 voltage trip points available

Description : ECONOLINE DC/DC-Converter

2.2 Watt DIP24 & SMD Single & Dual Output

Features
Regulated Converters
● 2.2W DIP Package
● 1kVDC, 2kVDC & 3kVDC Isolation Options
● Regulated Output
● Wide Input Range 2 : 1 and 4 : 1
● UL94V-0 Package Material
● ConTinuous Short Circuit Protection
● Cost Effective
● 100% Burned In
● Efficiency to 84%

Description : PCN10, 12, 13 Series (Product Compliant to DIN Standard: through hole,Wrapping Type)

■ Features
1. Compliant with DIN Standard
    Comply with IEC603-2/DIN41612 standard.
2. Variation in number of contacts
    10, 16, 20, 24, 28, 30, 32, 44, 48, 50, 64, 90, 96, 100, 128, and
    144 contacts are available.
3. Two point contact construction
    PCN10 and 12 series are constructed with high reliable doublesided two point contacts.
    PCN13 series pursues after cost performance, and constructed
    with single sided two point contacts.
4. Broad applications
    DIN standard types of B, C, R, and Q are available. The flux tight
    product is available. The easy lock pin type to prefix the board is
    available.
5. Stacking height variation
    PCN10H series contains 25, 30, 35, 40 and 45mm stacking
    height.
6. Circuit protection function available
    PCN10MC series utilizes a sequence structure for circuit
    protection function.
7. Cable connector
    ID connector for ribbon cable is available.
    The connector is prepared for crimping connection for AWC#26
    to 30 cables.
   
■ Application
    Control equipment, exchange, measuring instruments etc.
   

Description : Polypropylene Pulse/High Frequency Capacitors R76 Series Double Metallized Polypropylene Film, Radial, DC and Pulse Applications (Automotive Grade)

Overview
The R76 Series is constructed of polypropylene film and double metallized polyester film as electrodes with radial leads of Tinned wire. The radial leads are electrically welded to the metal layer on the ends of the capacitor winding. The capacitor is encapsulated in a self-exTinguishing solvent resistant plastic case with thermosetTing resin material meeTing the UL 94V–0 requirements.

Benefts
• Voltage range: 250 – 2,000 VDC
• Capacitance range: 100 pF – 15 µF
• Lead Spacing: 7.5 mm – 37.5 mm
• Capacitance tolerance: ±5%, ±10%, ±20%
• Climatic category: 55/105/56 IEC 60068-1
• OperaTing temperature range of −55˚C to +105˚C
• RoHS compliance and lead-free terminations
• Tape and reel packaging in accordance with IEC 60286–2
• Self-healing
• Automotive (AEC–Q200) grades available up to lead spacing 22.5mm

Description : 2.5mm Pitch Connector for Discrete Wire Connection (Product Compliant with UL/CSA Standard)

■ Features
1. New Insulation Displacement and Crimping Ideas
   This connector is a new type to insert the ID contacts in the case. Using this method, the following merits can be gained.
   1 By using the ID contact and crimping contact together, different current capacity cables can be mixed in one case.
   2 After connection, the contact can be replaced in excellent maintainability.
   3 Because the insulation displacement area is protected by the case, high reliability can be assured.
   4 Since the insulation displacement process can be performed only by replacing the applicator of the exisTing crimping machine, no expensive machine for insulation displacement is required.
2. PotTing Header Available
   The high profile Header is also available, corresponding to the board potTing process (sealed with resin) as waterproof measures.
3. Broad Variations
   The single row and double row contacts are aligned for "Board to Cable" and "In-line" series, respectively, while standard Tin and gold plaTing products are available.
   (Refer to the applicable combination pattern on next page.)

■ Applications
   Business equipment, particularly including the copy machine and printer

Description : 2.5mm Pitch Connector for Discrete Wire Connection (Product Compliant with UL/CSA Standard)

■ Features
1. New Insulation Displacement and Crimping Ideas
   This connector is a new type to insert the ID contacts in the case. Using this method, the following merits can be gained.
   1 By using the ID contact and crimping contact together, different current capacity cables can be mixed in one case.
   2 After connection, the contact can be replaced in excellent maintainability.
   3 Because the insulation displacement area is protected by the case, high reliability can be assured.
   4 Since the insulation displacement process can be performed only by replacing the applicator of the exisTing crimping machine, no expensive machine for insulation displacement is required.

2. PotTing Header Available
   The high profile Header is also available, corresponding to the board potTing process (sealed with resin) as waterproof measures.
3. Broad Variations
   The single row and double row contacts are aligned for "Board to Cable" and "In-line" series, respectively, while standard Tin and gold plaTing products are available. (Refer to the applicable combination pattern on next page.)

Applications
   Business equipment, particularly including the copy machine and printer

Description : 4K SPI™ Bus Serial EEPROM

DESCRIPTION

The Microchip Technology Inc. 25AA040/25LC040/25C040 (25xx040*) is a 4K bit serial Electrically Erasable PROM. The memory is accessed via a simple Serial Peripheral Interface (SPI) compatible serial bus. The bus signals required are a clock input (SCK) plus separate data in (SI) and data out (SO) lines. Access to the device is controlled through a chip select (CS) input.



FEATURES

• Low power CMOS technology

   - Write current: 3 mA typical

   - Read current: 500 µA typical

   - Standby current: 500 nA typical

• 512 x 8 bit organization

• 16 byte page

• Write cycle time: 5ms max.

• Self-timed ERASE and WRITE cycles

• Block write protection

   - Protect none, 1/4, 1/2, or all of array

• Built-in write protection

   - Power on/off data protection circuitry

   - Write enable latch

   - Write protect pin

• Sequential read

• High reliability

   - Endurance: 10M cycles (guaranteed)

   - Data retention: > 200 years

   - ESD protection: > 4000 V

• 8-pin PDIP, SOIC, and TSSOP packages

• Temperature ranges supported:

   - Commercial: (C) 0°C to +70°C

   - Industrial: (I) -40°C to +85°C

   - Automotive: (E) (25C040) -40°C to +125°C



 


Description : 1K Microwire Compatible Serial EEPROM

Description:
The Microchip Technology Inc. 93XX46A/B/C devices are 1Kbit low-voltage serial Electrically Erasable PROMs (EEPROM). Word-selectable devices such as the 93AA46C, 93LC46C or 93C46C are dependent upon external logic levels driving the ORG pin to set word size. For dedicated 8-bit communication, the 93AA46A, 93LC46A or 93C46A devices are available, while the 93AA46B, 93LC46B and 93C46B devices provide dedicated 16-bit communication. Advanced CMOS technology makes these devices ideal for low power, nonvolatile memory applications. The entire 93XX Series is available in standard packages includ ing 8-lead PDIP and SOIC, and advanced packaging including 8-lead MSOP, 6-lead SOT-23, 8-lead 2x3 DFN/TDFN and 8-lead TSSOP. All packages are Pb-free (Matte Tin) finish.

Features:
• Low-Power CMOS Technology
• ORG Pin to Select Word Size for ‘46C’ Version
• 128 x 8-bit Organization ‘A’ Devices (no ORG)
• 64 x 16-bit Organization ‘B’ Devices (no ORG)
• Self-Timed Erase/Write Cycles (including Auto-Erase)
• Automatic Erase All (ERAL) Before Write All (WRAL)
• Power-On/Off Data Protection Circuitry
• Industry Standard 3-Wire Serial I/O
• Device Status Signal (Ready/Busy)
• Sequential Read Function
• 1,000,000 Erase/Write Cycles
• Data Retention > 200 Years
• RoHS Compliant
• Temperature Ranges Supported:
   - Industrial (I) -40°C to +85°C
   - Automotive (E) -40°C to +125°C

12345678910 Next



All Rights Reserved© datasheetq.com  [Privacy Policy ] [ Request Datasheet] [Contact Us]