Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Description + Content Search

Search Word's :

Part Name(s) : ST72324 ST72F324J2TA ST72F324J4TA ST72F324J6TA ST72F324K2TA ST72F324K4TA ST72F324K6TA ST72F324J6 ST72F324K6 ST72F324J4 ST-Microelectronics
STMicroelectronics
Description : 5V RANGE 8-BIT MCU WITH 8 TO 32K FLASH, 10-BIT ADC, 4 TIMERS, SPI, SCI INTERFACE View

INTRODUCTION
The ST72F324 devices are members of the ST7 microcontroller family designed for the 5V operating RANGE.

– The 32-pin devices are designed for mid-RANGE
   applications
– The 42/44-pin devices target the same RANGE of
   applications requiring more than 24 I/O ports.

For a description of the differences between ST72F324 and ST72F324B devices refer TO Section 14.3 on page 152 All devices are based on a common industry standard 8-BIT core, featuring an enhanced instruction set and are available WITH FLASH program memory.
Under software control, all devices can be placed in WAIT, SLOW, ACTIVE-HALT or HALT mode, reducing power consumption when the application is in idle or stand-by state.
The enhanced instruction set and addressing modes of the ST7 offer both power and flexibility TO software developers, enabling the design of highly efficient and compact application code. In addition TO standard 8-BIT data management, all ST7 microcontrollers feature true bit manipulation, 8x8 unsigned multiplication and indirect addressing modes.

■ Memories
   – 8 TO 32K dual voltage High Density Flash (HD
      Flash) WITH read-out protection capability. In
      Application Programming and In-Circuit Programming for HDFlash devices
   – 384 TO 1K bytes RAM
   – HDFlash endurance: 100 cycles, data retention: 20 years at 55°C
■ Clock, Reset And Supply Management
   – Enhanced low voltage supervisor (LVD) for
      main supply WITH programmable reset thresh
      olds and auxiliary voltage detecTOr (AVD) WITH
      interrupt capability
   – Clock sources: crystal/ceramic resonaTOr os
      cillaTOrs, internal RC oscillaTOr, clock security
      system and bypass for external clock
   – PLL for 2x frequency multiplication
   – Four Power Saving Modes: Halt, Active-Halt,
      Wait and Slow
■ Interrupt Management
   – Nested interrupt controller
   – 10 interrupt vecTOrs plus TRAP and RESET
   – 9/6 external interrupt lines (on 4 vecTOrs)
■ Up TO 32 I/O Ports
   – 32/24 multifunctional bidirectional I/O lines
   – 22/17 alternate function lines
   – 12/10 high sink outputs
■ 4 Timers
   – Main Clock Controller WITH: Real time base,
      Beep and Clock-out capabilities
   – Configurable watchdog timer
   – 16-bit Timer A WITH: 1 input capture, 1 output
      compare, external clock input, PWM and
      pulse generaTOr modes
   – 16-bit Timer B WITH: 2 input captures, 2 output
   compares, PWM and pulse generaTOr modes
■ 2 Communication Interfaces
   – SPI synchronous serial interface
   – SCI asynchronous serial interface
■ 1 Analog Peripheral (low current coupling)
   – 10-BIT ADC WITH up TO 12 robust input ports
■ Instruction Set
   – 8-BIT Data Manipulation
   – 63 Basic Instructions
   – 17 main Addressing Modes
   – 8 x 8 Unsigned Multiply Instruction
■ Development TOols
   – Full hardware/software development package
   – In-Circuit Testing capability

Part Name(s) : ST72324BL ST72324BLJ2BA ST72324BLJ2TA ST72324BLJ4 ST72324BLJ4BA ST72324BLJ4TA ST72324BLK2BA ST72324BLK2TA ST72324BLK4BA ST72324BLK4TA ST-Microelectronics
STMicroelectronics
Description : 3V RANGE 8-BIT MCU WITH 8 TO 32K FLASH/ROM, 10-BIT ADC, 4 TIMERS, SPI, SCI INTERFACE View

INTRODUCTION

The ST72F324L and ST72324BL devices are members of the ST7 microcontroller family designed for the 3V operating RANGE. They can be grouped as follows:

   – The 32-pin devices are designed for mid-RANGE applications

   – The 44-pin devices target the same RANGE of applications requiring more than 24 I/O ports.

All devices are based on a common industry standard 8-BIT core, featuring an enhanced instruction set and are available WITH FLASH or ROM program memory.



■ Memories

   – 8 TO 32K dual voltage High Density Flash (HD Flash) or ROM WITH read-out protection capability. In-Application Programming and In Circuit Programming for HDFlash devices

   – 384 TO 1K bytes RAM

   – HDFlash endurance: 100 cycles, data retention: 20 years at 55°C

■ Clock, Reset And Supply Management

   – Clock sources: crystal/ceramic resonaTOr os cillaTOrs, internal RC oscillaTOr, and bypass for external clock

   – PLL for 2x frequency multiplication

   – Four Power Saving Modes: Halt, Active-Halt, Wait and Slow

■ Interrupt Management

   – Nested interrupt controller

   – 10 interrupt vecTOrs plus TRAP and RESET

   – 9/6 external interrupt lines (on 4 vecTOrs)

■ Up TO 32 I/O Ports

   – 32/24 multifunctional bidirectional I/O lines

   – 22/17 alternate function lines

   – 12/10 high sink outputs

■ 4 Timers

   – Main Clock Controller WITH: Real time base, Beep and Clock-out capabilities

   – Configurable watchdog timer

   – 16-bit Timer A WITH: 1 input capture, 1 output compare, external clock input, PWM and pulse generaTOr modes

   – 16-bit Timer B WITH: 2 input captures, 2 output compares, PWM and pulse generaTOr modes

■ 2 Communication Interfaces

   – SPI synchronous serial interface

   – SCI asynchronous serial interface

■ 1 Analog Peripheral

   – 10-BIT ADC WITH up TO 12 input ports

■ Instruction Set

   – 8-BIT Data Manipulation

   – 63 Basic Instructions

   – 17 main Addressing Modes

   – 8 x 8 Unsigned Multiply Instruction

■ Development TOols

   – Full hardware/software development package

   – In-Circuit Testing capability



 


Part Name(s) : ST7250 ST7250A6 ST7250B4 ST-Microelectronics
STMicroelectronics
Description : 8-BIT MCU FOR CAN WITH 32K ROM, 1K RAM, EEPROM, ADC, WDG, PWM/BRM, 2 TIMERS, SPI AND SCI INTERFACES View

8-BIT MCU FOR CAN WITH 32K ROM, 1K RAM, EEPROM, ADC, WDG, PWM/BRM, 2 TIMERS, SPI AND SCI INTERFACES

Part Name(s) : ST72324J2 ST72324J2T3 ST72324J4 ST72324J6 ST72324JK ST72324JK2 ST72F324J ST72324JX ST72324K2B3 ST72324K4 ST-Microelectronics
STMicroelectronics
Description : 5V RANGE 8-BIT MCU WITH 8 TO 32K FLASH, 10-BIT ADC, 4 TIMERS, SPI, SCI INTERFACE View

INTRODUCTION
The ST72324 devices are members of the ST7 microcontroller family designed for the 5V operating RANGE.
    – The 32-pin devices are designed for mid-RANGE applications
    – The 42/44-pin devices target the same RANGE of applications requiring more than 24 I/O ports.

■ Memories
    – 8 TO 32K dual voltage High Density Flash (HDFlash) WITH read-out protection capability. InApplication Programming and In-Circuit Programming for HDFlash devices
    – 384 TO 1K bytes RAM
    – HDFlash endurance: 100 cycles, data retention: 20 years at 55°C
■ Clock, Reset And Supply Management
    – Enhanced low voltage supervisor (LVD) for main supply WITH programmable reset thresholds and auxiliary voltage detecTOr (AVD) WITH interrupt capability
    – Clock sources: crystal/ceramic resonaTOr oscillaTOrs, internal RC oscillaTOr, clock security system and bypass for external clock
    – PLL for 2x frequency multiplication
    – Four Power Saving Modes: Halt, Active-Halt, Wait and Slow
■ Interrupt Management
    – Nested interrupt controller
    – 10 interrupt vecTOrs plus TRAP and RESET
    – 9/6 external interrupt lines (on 4 vecTOrs)
■ Up TO 32 I/O Ports
    – 32/24 multifunctional bidirectional I/O lines
    – 22/17 alternate function lines
    – 12/10 high sink outputs
■ 4 Timers
    – Main Clock Controller WITH: Real time base, Beep and Clock-out capabilities
    – Configurable watchdog timer
    – 16-bit Timer A WITH: 1 input capture, 1 output compare, external clock input, PWM and pulse generaTOr modes
    – 16-bit Timer B WITH: 2 input captures, 2 output compares, PWM and pulse generaTOr modes
■ 2 Communication Interfaces
    – SPI synchronous serial interface
    – SCI asynchronous serial interface
■ 1 Analog Peripheral (low current coupling)
    – 10-BIT ADC WITH up TO 12 robust input ports
■ Instruction Set
    – 8-BIT Data Manipulation
    – 63 Basic Instructions
    – 17 main Addressing Modes
    – 8 x 8 Unsigned Multiply Instruction
■ Development TOols
    – Full hardware/software development package
    – In-Circuit Testing capability


Part Name(s) : STM8S005C6 STM8S005K6 STM8S005C6T6 STM8S005C6T6TR STM8S005C6T6C STM8S005C6T6CTR STM8S005K6T6 STM8S005K6T6TR STM8S005K6T6C STM8S005K6T6CTR ST-Microelectronics
STMicroelectronics
Description : Value line, 16 MHz STM8S 8-BIT MCU, 32 Kbytes FLASH, data EEPROM,10-BIT ADC, TIMERS, UART, SPI, I²C View

Introduction
This datasheet contains the description of the device features, pinout, electrical characteristics, mechanical data and ordering information.
• For complete information on the STM8S microcontroller memory, registers and peripherals, please refer TO the STM8S microcontroller family reference manual (RM0016).
• For information on programming, erasing and protection of the internal Flash memory please refer TO the STM8S Flash programming manual (PM0051).
• For information on the debug and SWIM (single wire interface module) refer TO the STM8 SWIM communication proTOcol and debug module user manual (UM0470).
• For information on the STM8 core, please refer TO the STM8 CPU programming manual (PM0044).

Description
The STM8S005xx value line 8-BIT microcontrollers offer 32 Kbytes of Flash program memory, plus 128 bytes of data EEPROM. They are referred TO as medium-density devices in the STM8S microcontroller family reference manual (RM0016). All devices of the STM8S005xx value line provide the following benefits: performance, robustness, reduced system cost, and short develoment cycles.
Device performance and robustness are ensured by true data EEPROM supporting up TO 100 000 write/erase cycles, advanced core and peripherals made in a state-of-the art technology, a 16 MHz clock frequency, robust I/Os, independent watchdogs WITH separate clock source, and a clock security system.
The system cost is reduced thanks TO high system integration level WITH internal clock oscillaTOrs, watchdog and brown-out reset.
Common family product architecture WITH compatible pinout, memory map and modular peripherals allow application scalability and reduced development cycles.
All products operate from a 2.95 TO 5.5 V supply voltage.
Full documentation is offered as well as a wide choice of development TOols.

Features
Core
   • 16 MHz advanced STM8 core WITH Harvard architecture and 3-stage pipeline
   • Extended instruction set
Memories
   • Medium-density Flash/EEPROM:
      - Program memory: 32 Kbytes of Flash memory; data retention 20 years at 55°C after 100 cycles
      - Data memory: 128 bytes of true data EEPROM; endurance up TO 100 k write/erase cycles
   • RAM: 2 Kbytes
Clock, reset and supply management
   • 2.95 V TO 5.5 V operating voltage
   • Flexible clock control, 4 master clock sources:
      - Low power crystal resonaTOr oscillaTOr
      - External clock input
      - Internal, user-trimmable 16 MHz RC
      - Internal low power 128 kHz RC
   • Clock security system WITH clock moniTOr
   • Power management:
      - Low power modes (wait, active-halt, halt)
      - Switch-off peripheral clocks individually
   • Permanently active, low consumption power-on and power-down reset
Interrupt management
   • Nested interrupt controller WITH 32 interrupts
   • Up TO 37 external interrupts on 6 vecTOrs
Timers
   • 2x 16-bit general purpose TIMERS, WITH 2+3 CAPCOM channels (IC, OC or PWM)
   • Advanced control timer: 16-bit, 4 CAPCOM channels, 3 complementary outputs, dead-time insertion and flexible synchronization
   • 8-BIT basic timer WITH 8-BIT prescaler
   • AuTO wake-up timer
   • Window and independent watchdog timers
Communications interfaces
   • UART WITH clock output for synchronous operation, Smartcard, IrDA, LIN
   • SPI interface up TO 8 Mbit/s
   • I2C interface up TO 400 Kbit/s
Analog-TO-digital converter (ADC)
   • 10-BIT, ±1 LSB ADC WITH up TO 10 multiplexed channels, scan mode and analog watchdog
I/Os
   • Up TO 38 I/Os on a 48-pin package including 16 high sink outputs
   • Highly robust I/O design, immune against current injection
Development support
   • Embedded single wire interface module (SWIM) for fast on-chip programming and non intrusive debugging

Part Name(s) : ST72521 ST72521AR6T1 ST72521AR6T5 ST72521AR6T6 ST72521AR6TA ST72521AR6TB ST72521AR6TC ST72521AR9T1 ST72521AR9T5 ST72521AR9T6 ST-Microelectronics
STMicroelectronics
Description : 8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, FIVE TIMERS, SPI, SCI, I2C, CAN INTERFACE View

INTRODUCTION

The ST72521(A)R and ST72521M devices are members of the ST7 microcontroller family designed for mid-RANGE applications WITH a CAN bus interface (Controller Area Network). All devices are based on a common industry standard 8-BIT core, featuring an enhanced instruction set and are available WITH FLASH or ROM program memory.



■ Memories

32K TO 60K dual voltage High Density Flash (HDFlash) or ROM WITH read-out protection capability. In-Application Programming and In-Circuit Programming for HDFlash devices

– 1K TO 2K RAM

– HDFlash endurance: 100 cycles, data retention: 20 years at 55°C

■ Clock, Reset And Supply Management

– Enhanced low voltage supervisor (LVD) for main supply and auxiliary voltage detecTOr (AVD) WITH interrupt capability

– Clock sources: crystal/ceramic resonaTOr oscillaTOrs, internal RC oscillaTOr, clock security system and bypass for external clock

– PLL for 2x frequency multiplication

– Four power saving modes: Halt, Active-Halt, Wait and Slow

■ Interrupt Management

– Nested interrupt controller

– 14 interrupt vecTOrs plus TRAP and RESET

TOp Level Interrupt (TLI) pin

– 15 external interrupt lines (on 4 vecTOrs)

■ Up TO 64 I/O Ports

– 48 multifunctional bidirectional I/O lines

– 34 alternate function lines

– 16 high sink outputs

■ 5 Timers

– Main Clock Controller WITH: Real time base, Beep and Clock-out capabilities

– Configurable watchdog timer

– Two 16-bit timers WITH: 2 input captures, 2 out put compares, external clock input on one timer, PWM and pulse generaTOr modes

8-BIT PWM AuTO-Reload timer WITH: 2 input captures, 4 PWM outputs, output compare Device Summary and time base interrupt, external clock WITH event detecTOr

■ 4 Communications Interfaces

– SPI synchronous serial interface

– SCI asynchronous serial interface (LIN compatible)

–I2C multimaster interface

– CAN interface (2.0B Passive)

■ Analog peripheral

10-BIT ADC WITH 16 input pins

■ Instruction Set

8-BIT Data Manipulation

– 63 Basic Instructions

– 17 main Addressing Modes

– 8 x 8 Unsigned Multiply Instruction

■ Development TOols

– Full hardware/software development package

– In-Circuit Testing capability


Part Name(s) : 8S003F3P6 ST-Microelectronics
STMicroelectronics
Description : Value line, 16 MHz STM8S 8-BIT MCU,8 Kbyte FLASH, 128 byte data EEPROM, 10-BIT ADC, 3 timers View

The STM8S003F3/K3 value line 8-BIT microcontrollers offer 8 Kbyte Flash program memory,

plus integrated true data EEPROM. They are referred TO as low-density devices in the

STM8S microcontroller family reference manual (RM0016).







TheSTM8S003F3/K3 value line devices provide the following benefits: performance,

robustness and reduced system cost.


Part Name(s) : ST72F621 ST72F621J2M1 ST72F622 ST72F622K2M1 ST72F622L2B1 ST72F623 ST72F623F2T1 ST72P621 ST72P621K4M1 ST72P621L4B1 ST-Microelectronics
STMicroelectronics
Description : LOW SPEED USB 8-BIT MCU WITH 3 ENDPOINTS, FLASH OR ROM MEMORY, LVD, WDG, 10-BIT ADC, 2 TIMERS, SCI, SPI View

Features
■ Memories
– 8 or 16 Kbyte Program memory
(ROM or Dual voltage FLASH)
WITH read-write protection
– In-Application and In-Circuit Programming for
FLASH versions
– 384 TO 768 bytes RAM (128-byte stack)
■ Clock, Reset and Supply Management
– Enhanced Reset System (Power On Reset)
– Low Voltage DetecTOr (LVD)
– Clock-out capability
– 6 or 12 MHz OscillaTOr (8, 4, 2, 1 MHz internal
frequencies)
– 3 Power saving modes
■ USB (Universal Serial Bus) Interface
– DMA for low speed applications compliant
WITH USB specification (version 2.0):
– Integrated 3.3V voltage regulaTOr and trans
ceivers
– Suspend and Resume operations
– 3 Endpoints
■ Up TO 31 I/O Ports
– Up TO 31 multifunctional bidirectional I/O lines
– Up TO 12 External interrupts (3 vecTOrs)
– 13 alternate function lines
– 8 high sink outputs
(8 TO:mA@0.4" data-cke-saved-href="mailTO:mA@0.4">mA@0.4 V/20 TO:mA@1.3" data-cke-saved-href="mailTO:mA@1.3">mA@1.3 V)
– 2 true open drain pins (N buffer 8 TO:mA@0.4" data-cke-saved-href="mailTO:mA@0.4">mA@0.4 V)
■ 3 Timers
– Configurable watchdog timer (8 TO 500 ms
timeout)
8-BIT AuTO Reload Timer (ART) WITH 2 Input
Captures, 2 PWM outputs and External Clock
8-BIT Time Base Unit (TBU) for generating periodic interrupts cascadable WITH ART
■ Analog Peripheral
10-BIT A/D Converter WITH up TO 8 input pins.
■ 2 Communications Interfaces
– Asynchronous Serial Communication inter
face
– Synchronous Serial Peripheral Interface
■ Instruction Set
8-BIT data manipulation
– 63 basic instructions
– 17 main addressing modes
– 8 x 8 unsigned multiply instruction
– True bit manipulation
■ Nested interrupts
■ Development TOols
– Full hardware/software development package

Part Name(s) : C8051F006 C8051F006-GQ Silabs
Silicon Laboratories
Description : 25 MIPS, 32 kB FLASH, 12-Bit ADC, 48-Pin Mixed-Signal MCU View

25 MIPS, 32 kB FLASH, 12-Bit ADC, 48-Pin Mixed-Signal MCU


12345678910 Next



All Rights Reserved© datasheetq.com 2015 - 2019  [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]