Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Description + Content Search

Search Word's :

Part Name(s) : SAM4S Atmel
Atmel Corporation
Description : AT91SAM ARM-based Flash MCU View

Description

The Atmel SAM4S series is a member of a family of Flash microcontrollers based on the high

performance 32-bit ARM Cortex-M4 RISC processor. It operates at a maximum speed of 120 MHz and features up to 2048 Kbytes of Flash, with optional dual bank implementation and cache memory, and up to 160 Kbytes of SRAM.



Features

• Core

– ARM®Cortex®-M4 with a 2Kbytes cache running at up to 120 MHz

– Memory Protection Unit (MPU)

– DSP Instruction Set

–Thumb®-2 instruction set

• Pin-to-pin compatible with SAM3N, SAM3S products (64- and 100- pin versions) and SAM7S legacy products (64-pin version)

• Memories

– Up to 2048 Kbytes embedded Flash withoptional dual bank and cache memory

– Up to 160 Kbytes embedded SRAM

– 16 Kbytes ROM with embedded boot loaderroutines (UART, USB) and IAP routines

– 8-bit Static Memory Controller (SMC): SRAM, PSRAM, NOR and NAND Flash support

• System

– Embedded voltage regulator for single supply operation

– Power-on-Reset (POR), Brown-out Detector(BOD) and Watchdog for safe operation

– Quartz or ceramic resonator oscillators: 3 to 20 MHz main power with Failure Detection and optional low-power 32.768 kHz for RTC or device clock

– RTC with Gregorian and Persian Calendar mode, waveform generation in low power modes

– RTC clock calibration circuitry for 32.768 kHz crystal frequency compensation

– High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz default frequency for device startup. In-application trimming access for frequency adjustment

– Slow Clock Internal RC oscillator as permanent low-power mode device clock

– Two PLLs up to 240 MHz for device clock and for USB

– Temperature Sensor

– Up to 22 Peripheral DMA (PDC) Channels


Part Name(s) : VI-ARM VI-ARM-1 VI-ARM-2 VI-ARM-C11 VI-ARM-C12 VI-ARM-C1N VI-ARM-C1S VI-ARM-C21 VI-ARM-C22 VI-ARM-C2N Vicor
Vicor
Description : VI-ARM™ Autoranging Rectifier Modules Up to 1500 Watts View

Product Highlights

The ARM (Autoranging Rectifier Module) is an AC front end module which provides autoranging line rectification and inrush current limiting. The ARM is available in either 500/750W or 750/1000W models in a

mini sized package measuring only 2.28" x 1.45" x 0.5".



Features

• Autoranging input

• Microprocessor controlled

• VI-ARM-1

  500 Watts @ 90-132Vac

  750 Watts @ 180-264Vac

• VI-ARM-2

  1000 Watts @ 90-132Vac

  1500 Watts @ 180-264Vac

• 96-98% Efficiency

• 100˚C baseplate (no derating)

• UL, CSA, TÜV, VDE, BABT

• AC Bus OK, module enable

• Inrush limiting (no external circuitry)

• CE Marked



Typical Applications: systems requiring a rugged, full featured interface to the AC mains in the smallest possible package.


Part Name(s) : AT91SAM7S128 AT91SAM7S128-AU-001 AT91SAM7S128C-AU-999 AT91SAM7S128D-AU AT91SAM7S256-AU-001 AT91SAM7S256-MU AT91SAM7S256D-AU AT91SAM7S256D-MU AT91SAM7S32-AU-001 AT91SAM7S321-MU Atmel
Atmel Corporation
Description : ARMMCU 256K Flash SRAM 64K ARM based MCU View

Atmel’s SAM7S is a series of low pincount Flash microcontrollers based on the 32-bit ARM RISC processor. It features a high-speed Flash and an SRAM, a large set of peripherals, including a USB 2.0 device (except for the SAM7S32 and SAM7S16), and a complete set of system functions minimizing the number of external components. The device is an ideal migration path for 8-bit microcontroller users looking for additional performance and extended memory.





The Atmel® | SMART ARM®-based SAM7S256 is a member of the SAM7S series of Flash microcontrollers based on the 32-bit ARM7TDMI® RISC processor. It operates at a maximum speed of 55MHz and features 128KB of Flash memory and 64KB of SRAM. The peripheral set includes a Full Speed USB device and Phy at 12Mbps, UART, two USARTs, TWI (I2C), SPI, SSC, two PWM timers, three 16-bit timers, RTT, 8x10-bit ADC and 32 IO lines. It achieves single-cycle instruction access from embedded Flash at 27 MIPS. The multi-layer bus matrix, multiple SRAM banks, PDC, and DMA support parallel tasks and maximize data throughput. The SAM7S256 operates from 1.65V to 3.6V and is available in 64-pin LQFP and QFN packages.



 



Official Site : http://www.atmel.com/devices/SAM7S256.aspx


Part Name(s) : ATSAM3A ATSAM3A4CA-AU ATSAM3A4CA-CU ATSAM3A8CA-AU ATSAM3A8CA-CU ATSAM3X ATSAM3X4CA-AU ATSAM3X4CA-CU ATSAM3X4EA-AU ATSAM3X4EA-CU Atmel
Atmel Corporation
Description : AT91SAM ARM-based Flash MCU View

SAM3X/A Description

Atmel’s SAM3X/A series is a member of a family of Flash microcontrollers based on the high performance 32-bit ARM Cortex-M3 RISC processor. It operates at a maximum speed of 84 MHz and features up to 512 Kbytes of Flash and up to 100 Kbytes of SRAM. The peripheral set includes a High Speed USB Host and Device port with embedded transceiver, an Ethernet MAC, 2x CANs, a High Speed MCI for SDIO/SD/MMC, an External Bus Interface with NAND Flash controller, 5x UARTs, 2x TWIs, 4x SPIs, as well as 1 PWM timer, 9x general-purpose 32-bit timers, an RTC, a 12-bit ADC and a 12-bit DAC.



Features

• Core

   – ARM® Cortex®-M3 revision 2.0 running at up to 84 MHz

   – Memory Protection Unit (MPU)

   – Thumb®-2 instruction set

   – 24-bit SysTick Counter

   – Nested Vector Interrupt Controller

• Memories

   – From 256 to 512 Kbytes embedded Flash, 128-bit wide access, memory accelerator, dual bank

   – From 32 to 100 Kbytes embedded SRAM with dual banks

   – 16 Kbytes ROM with embedded bootloader routines (UART, USB) and IAP routines

   – Static Memory Controller (SMC): SRAM, NOR, NAND support. NAND Flash controller with 4-kbyte RAM buffer and ECC

• System

   – Embedded voltage regulator for single supply operation

   – POR, BOD and Watchdog for safe reset

   – Quartz or ceramic resonator oscillators: 3 to 20 MHz main and optional low power 32.768 kHz for RTC or device clock.

   – High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz Default Frequency for fast device startup

   – Slow Clock Internal RC oscillator as permanent clock for device clock in low power mode

   – One PLL for device clock and one dedicated PLL for USB 2.0 High Speed Mini Host/Device

   – Temperature Sensor

   – Up to 17 peripheral DMA (PDC) channels and 6-channel central DMA plus dedicated DMA for High-Speed USB Mini Host/Device and Ethernet MAC

• Low Power Modes

   – Sleep and Backup modes, down to 2.5 µA in Backup mode.

   – Backup domain: VDDBU pin, RTC, eight 32-bit backup registers

   – Ultra Low-power RTC

• Peripherals

   – USB 2.0 Device/Mini Host: 480 Mbps, 4-kbyte FIFO, up to 10 bidirectional Endpoints, dedicated DMA

   – Up to 4 USARTs (ISO7816, IrDA®, Flow Control, SPI, Manchester and LIN support) and one UART

   – 2 TWI (I2C compatible), up to 6 SPIs, 1 SSC (I2S), 1 HSMCI (SDIO/SD/MMC) with up to 2 slots

   – 9-Channel 32-bit Timer/Counter (TC) for capture, compare and PWM mode, Quadrature Decoder Logic and 2-bit Gray Up/Down Counter for Stepper Motor

   – Up to 8-channel 16-bit PWM (PWMC) with Complementary Output, Fault Input, 12-bit Dead Time Generator Counter for Motor Control

   – 32-bit Real Time Timer (RTT) and RTC with calendar and alarm features

   – 16-channel 12-bit 1Msps ADC with differential input mode and programmable gain stage

   – One 2-channel 12-bit 1 Msps DAC

   – One Ethernet MAC 10/100 (EMAC) with dedicated DMA

   – Two CAN Controller with eight Mailboxes

   – One True Random Number Generator (TRNG)

   – Write Protected Registers

• I/O

   – Up to 103 I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and on-die Series Resistor Termination

   – Up to Six 32-bit Parallel Input/Outputs (PIO)

• Packages

   – 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm

   – 100-ball LFBGA, 9 x 9 mm, pitch 0.8 mm

   – 144-lead LQFP, 20 x 20 mm, pitch 0.5 mm

   – 144-ball LFBGA, 10 x 10 mm, pitch 0.8 mm



 



Part Name(s) : STM32F103C6 STM32F103C6T6 STM32F103C8 STM32F103C8T6 STM32F103R6 STM32F103R6T6 STM32F103R8 STM32F103R8T6 STM32F103RB STM32F103V8 ST-Microelectronics
STMicroelectronics
Description : Performance line, ARM-based 32-bit MCU with Flash, USB, CAN, seven 16-bit timers, two ADCs and nine communication interfaces View

Features

■ Core: ARM 32-bit Cortex™-M3 CPU

– 72 MHz, 90 DMIPS with 1.25 DMIPS/MHz

– Single-cycle multiplication and hardware division

– Nested interrupt controller with 43 maskable interrupt channels

– Interrupt processing (down to 6 CPU cycles) with tail chaining

■ Memories

– 32-to-128 Kbytes of Flash memory

– 6-to-20 Kbytes of SRAM

■ Clock, reset and supply management

– 2.0 to 3.6 V application supply and I/Os

– POR, PDR, and programmable voltage detector (PVD)

– 4-to-16 MHz quartz oscillator

– Internal 8 MHz factory-trimmed RC

– Internal 32 kHz RC

– PLL for CPU clock

– Dedicated 32 kHz oscillator for RTC with calibration

■ Low power

– Sleep, Stop and Standby modes

– VBAT supply for RTC and backup registers

■ 2 x 12-bit, 1 µs A/D converters (16-channel)

– Conversion range: 0 to 3.6 V

– Dual-sample and hold capability

– Synchronizable with advanced control timer

– Temperature sensor

■ DMA

– 7-channel DMA controller

– Peripherals supported: timers, ADC, SPIs, I2Cs and USARTs


Part Name(s) : ATSAM3N-EK ATSAM3S-EK ATSAM3U-EK AT91SAM7L-STK AT91SAM7S-EK AT91SAM7SE-EK AT91SAM7X-EK AT91SAM9G20-EK AT91SAM9260-EK AT91SAM9XE-EK Atmel
Atmel Corporation
Description : Atmel Evaluation Kits View

Atmel Evaluation Kits

Atmel 32-bit Flash-based ARM Microcontrollers

One-stop shop for ARM-based Microcontrollers

Part Name(s) : ATSAM4S16BA-AU ATSAM4S16BA-MU ATSAM4S16CA-AU ATSAM4S16CA-CFU ATSAM4S16CA-CU ATSAM4S8BA-AU ATSAM4S8BA-MU ATSAM4S8CA-AU ATSAM4S8CA-CFU ATSAM4S8CA-CU Atmel
Atmel Corporation
Description : AT91SAM ARM-based Flash MCU View

Description

The Atmel SAM4S series is a member of a family of Flash microcontrollers based on the high performance 32-bit ARM Cortex-M4 RISC processor. It operates at a maximum speed of 120 MHz and features up to 2048 Kbytes of Flash, with optional dual bank implementation and cache memory, and up to 160 Kbytes of SRAM. The peripheral set includes a Full Speed USB Device port with embedded transceiver, a High Speed MCI for SDIO/SD/MMC, an External Bus Interface featuring a Static Memory Controller providing connection to SRAM, PSRAM, NOR Flash, LCD Module and NAND Flash, 2x USARTs, 2x UARTs, 2x TWIs, 3x SPI, an I2S, as well as 1 PWM timer, 2x three channel general-purpose 16-bit timers (with stepper motor and quadrature decoder logic support), an RTC, a 12-bit ADC, a 12-bit DAC and an analog comparator.



Features

• Core

– ARM® Cortex®-M4 with a 2Kbytes cache running at up to 120 MHz

– Memory Protection Unit (MPU)

– DSP Instruction Set

– Thumb®-2 instruction set

• Pin-to-pin compatible with SAM3N, SAM3S products (64- and 100- pin versions) and SAM7S legacy products (64-pin version)

• Memories

– Up to 2048 Kbytes embedded Flash with optional dual bank and cache memory

– Up to 160 Kbytes embedded SRAM

– 16 Kbytes ROM with embedded boot loader routines (UART, USB) and IAP routines

– 8-bit Static Memory Controller (SMC): SRAM, PSRAM, NOR and NAND Flash support

• System

– Embedded voltage regulator for single supply operation

– Power-on-Reset (POR), Brown-out Detector (BOD) and Watchdog for safe operation

– Quartz or ceramic resonator oscillators: 3 to 20 MHz main power with Failure Detection and optional low-power 32.768 kHz for RTC or device clock

– RTC with Gregorian and Persian Calendar mode, waveform generation in low power modes

– RTC clock calibration circuitry for 32.768 kHz crystal frequency compensation

– High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz default frequency for device startup. In-application trimming access for frequency adjustment

– Slow Clock Internal RC oscillator as permanent low-power mode device clock

– Two PLLs up to 240 MHz for device clock and for USB

– Temperature Sensor

– Up to 22 Peripheral DMA (PDC) Channels

• Low Power Modes

– Sleep and Backup Modes, down to 1 µA in Backup Mode

– Ultra low-power RTC

• Peripherals

– USB 2.0 Device: 12 Mbps, 2668 byte FIFO, up to 8 bidirectional Endpoints. On-Chip

Transceiver

– Up to 2 USARTs with ISO7816, IrDA®, RS-485, SPI, Manchester and Modem Mode

– Two 2-wire UARTs

– Up to 2 Two Wire Interface (I2C compatible), 1 SPI, 1 Serial Synchronous Controller

(I2S), 1 High Speed Multimedia Card Interface (SDIO/SD Card/MMC)

– 2 Three-Channel 16-bit Timer/Counter with capture, waveform, compare and PWM

mode. Quadrature Decoder Logic and 2-bit Gray Up/Down Counter for Stepper

Motor

– 4-channel 16-bit PWM with Complementary Output, Fault Input, 12-bit Dead Time

Generator Counter for Motor Control

– 32-bit Real-time Timer and RTC with calendar and alarm features

– Up to 16-channel, 1Msps ADC with differential input mode and programmable gain

stage and auto calibration

– One 2-channel 12-bit 1Msps DAC

– One Analog Comparator with flexible input selection, Selectable input hysteresis

– 32-bit Cyclic Redundancy Check Calculation Unit (CRCCU)

– Write Protected Registers

• I/O

– Up to 79 I/O lines with external interrupt capability (edge or level sensitivity),

debouncing, glitch filtering and on-die Series Resistor Termination

– Three 32-bit Parallel Input/Output Controllers, Peripheral DMA assisted Parallel

Capture Mode

• Packages

– 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm/ 100-ball TFBGA, 9 x 9 mm, pitch 0.8 mm/

100-ball VFBGA, 7 x 7 mm, pitch 0.65 mm

– 64-lead LQFP, 10 x 10 mm, pitch 0.5 mm/ 64-pad QFN 9x9 mm, pitch 0.5 mm


Part Name(s) : STM32F070C6 STM32F070CB STM32F070F6 STM32F070RB STM32F070F6P6 STM32F070F6P6TR STM32F070F6T6 STM32F070F6T6TR STM32F070FBP6 STM32F070FBP6TR ST-Microelectronics
STMicroelectronics
Description : ARM®-based 32-bit MCU, up to 128 KB Flash, USB FS 2.0, 11 timers, ADC, communication interfaces, 2.4 - 3.6 V View

Description
The STM32F070CB/RB/C6/F6 microcontrollers incorporate the high-performance ARM® Cortex®-M0 32-bit RISC core operating at a 48 MHz frequency, high-speed embedded memories (up to 128 Kbytes of Flash memory and up to 16 Kbytes of SRAM), and an extensive range of enhanced peripherals and I/Os. All devices offer standard communication interfaces (up to two I2Cs, up to two SPIs and up to four USARTs), one USB Full speed device, one 12-bit ADC, seven general-purpose 16-bit timers and an advancedcontrol PWM timer.
   
Features
• Core: ARM® 32-bit Cortex®-M0 CPU,
    frequency up to 48 MHz
• Memories
    – 32 to 128 Kbytes of Flash memory
    – 6 to 16 Kbytes of SRAM with HW parity
• CRC calculation unit
• Reset and power management
    – Digital & I/Os supply: VDD = 2.4 V to 3.6 V
    – Analog supply: VDDA = VDD to 3.6 V
    – Power-on/Power down reset (POR/PDR)
    – Low power modes: Sleep, Stop, Standby
• Clock management
    – 4 to 32 MHz crystal oscillator
    – 32 kHz oscillator for RTC with calibration
    – Internal 8 MHz RC with x6 PLL option
    – Internal 40 kHz RC oscillator
• Up to 51 fast I/Os
    – All mappable on external interrupt vectors
    – Up to 51 I/Os with 5V tolerant capability
• 5-channel DMA controller
• One 12-bit, 1.0 µs ADC (up to 16 channels)
    – Conversion range: 0 to 3.6 V
    – Separate analog supply: 2.4 V to 3.6 V
• Calendar RTC with alarm and periodic wakeup
    from Stop/Standby
• 11 timers
    – One 16-bit advanced-control timer for
        six-channel PWM output
    – Up to seven 16-bit timers, with up to four
        IC/OC, OCN, usable for IR control
        decoding
    – Independent and system watchdog timers
    – SysTick timer   
• Communication interfaces
    – Up to two I2C interfaces
    – Fast Mode Plus (1 Mbit/s) support, with
        20 mA current sink
    – SMBus/PMBus support (on single I/F)
    – Up to four USARTs supporting master
        synchronous SPI and modem control; one
        with auto baud rate detection
    – Up to two SPIs (18 Mbit/s) with 4 to 16
        programmable bit frames
    – USB 2.0 full-speed interface with BCD and
        LPM support
• Serial wire debug (SWD)
• All packages ECOPACK®2
   

Part Name(s) : LPC1774FBD144 LPC1774FBD208 LPC1776FBD208 LPC1776FET180 LPC1777FBD208 LPC1778FBD144 LPC1778FBD208 LPC1778FET180 LPC1778FET208 LPC177X NXP
NXP Semiconductors.
Description : 32-bit ARM Cortex-M3 microcontroller; up to 512 kB Flash and 6 kB SRAM; USB Device/Host/OTG; Ethernet; LCD; EMC View

The LPC178x/7x is an ARM Cortex-M3 based microcontroller for embedded applications requiring a high level of integration and low power dissipation.



The ARM Cortex-M3 is a next generation core that offers better performance than the ARM7 at the same clock rate and other system enhancements such as modernized debug features and a higher level of support block integration. The ARM Cortex-M3 CPU incorporates a 3-stage pipeline and has a Harvard architecture with separate local instruction and data buses, as well as a third bus with slightly lower performance for peripherals.



The ARM Cortex-M3 CPU also includes an internal prefetch unit that supports speculative branches.

The LPC178x/7x adds a specialized Flash memory accelerator to accomplish optimal performance when executing code from Flash. The LPC178x/7x operates at up to 120 MHz CPU frequency.


12345678910 Next



All Rights Reserved© datasheetq.com 2015 - 2019  [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]