1. Single N/N type Inverter

2. High Frequency Voltage Mode PWM Control

3. Easy Burst Dimming Control

4. External UVLO Function

5. Latched Mode Protection

6. Adjustable Shut-down time

7. Variable Protection function

FEATURES
1. Multi-function type with MOSFET  and optocoupler
   Instead of the conventional arrangement of a separate PhotoMOS relay and optocoupler, PhotoMOS relay and  2 optocoupler this new multi-function type  encapsulates the PhotoMOS relay and  optocoupler into one SOP package.
2. Ultra-small package size
   Integration of the two devices makes a  significant size reduction possible. The  SOP package measures (W) 4.4 × (D)  9.37 × (H) 2.1 mm ((W) .173× (D) .369× (H) .083 inch).
3. Ideal for PC card and Fax/Modem applications
   The small size provides additional space  for increased functionality, without sacrificing any of the performance of conventional MOSFET relay and optocoupler,  PhotoMOS relay and 2 optocoupler combinations. The new device has been specifically designed for the PCMCIA market.
4. Also available in 8-pin SOP package
   2 Form A MOSFET relays are also available in a single 8-pin SOP package.

TYPICAL APPLICATIONS
• PCMCIA/JEIDA standard FAX/Modem  card

GENERAL DESCRIPTION
The HMN28D are 16,384-bit, fully static, nonvolatile SRAM’s organized as 2,048 bytes by 8 bits. Each NVSRAM has a self-contained lithium energy source and control circuitry, which constantly monitors Vcc for an out-of-tolerance condition. When such a condition occurs, the lithium energy source is automatically switched on and writes protection is unconditionally enabled to prevent data corruption. The HMN28D devices can be used in place of existing 2K x 8 SRAM’s directly conforming to the popular byte wide 24-pin DIP standard. There is no limit on the number of write cycles that can be executed and no additional support circuitry is required for microprocessor interfacing.
The HMN28D uses extremely low standby current CMOS SRAM’s, coupled with small lithium coin cells to provide nonvolatility without long write-cycle times and the write-cycle limitations associated with EEPROM.

FEATURES
• Access time : 70, 85, 120 and 150ns
• High-density design : 2KByte Design
• Battery internally isolated until power is applied
• JEDEC standard 24-pin DIP Package
• Low-power CMOS
• Unlimited writes cycles
• Data retention in the absence of VCC
• 10-years minimum data retention in absence of power
• Automatic write-protection during power-up/power-down cycles
• Data is automatically protected during power loss
• Conventional SRAM operation; unlimited write cycles

GENERAL DESCRIPTION
The HMN28D are 16,384-bit, fully static, nonvolatile SRAM’s organized as 2,048 bytes by 8 bits. Each NVSRAM has a self-contained lithium energy source and control circuitry, which constantly monitors Vcc for an out-of-tolerance condition. When such a condition occurs, the lithium energy source is automatically switched on and writes protection is unconditionally enabled to prevent data corruption. The HMN28D devices can be used in place of existing 2K x 8 SRAM’s directly conforming to the popular byte wide 24-pin DIP standard. There is no limit on the number of write cycles that can be executed and no additional support circuitry is required for microprocessor interfacing.
The HMN28D uses extremely low standby current CMOS SRAM’s, coupled with small lithium coin cells to provide nonvolatility without long write-cycle times and the write-cycle limitations associated with EEPROM.

FEATURES
♦ Access time : 70, 85, 120 and 150ns
♦ High-density design : 2KByte Design
♦ Battery internally isolated until power is applied
♦ JEDEC standard 24-pin DIP Package
♦ Low-power CMOS
♦ Unlimited writes cycles
♦ Data retention in the absence of VCC
♦ 10-years minimum data retention in absence of power
♦ Automatic write-protection during power-up/power-down cycles
♦ Data is automatically protected during power loss
♦ Conventional SRAM operation; unlimited write cycles

DESCRIPTION
The PS2711-1 is an optically coupled isolator containing a GaAs light emitting diode and an NPN silicon phototransistor in a plastic SOP for high density applications.
The package is an SOP (Small Outline Package) type for high density mounting applications.

FEATURES
• High current transfer ratio (CTR = 200 % TYP. @ IF = 1mA)
• High isolation voltage (BV = 3 750 Vr.m.s.)
• Small and thin package (4-pin SOP)
• Ordering number of tape product: PS2711-1-F3, F4
• UL approved: File No. E72422 (S)

APPLICATIONS
• Programmable logic controllers
• Small power supply
• Hybrid IC
• Modem/FAX

DESCRIPTION
The TP4056 is a complete constant-current/constant-voltage linear charger for single cell lithium-ion batteries. Its SOP package and low external component count make the TP4056 ideally suited for portable applications. Furthermore, the TP4056 can work within USB and wall adapter.

FEATURES
• Programmable Charge Current Up to 1000mA
•·No MOSFET, Sense Resistor or Blocking Diode Required
•·Complete Linear Charger in SOP-8 Package for Single Cell Lithium-Ion Batteries
•·Constant-Current/Constant-Voltage
•·Charges Single Cell Li-Ion Batteries Directly from USB Port
•·Preset 4.2V Charge Voltage with 1.5% Accuracy
•·Automatic Recharge
•·two Charge Status Output Pins
•·C/10 Charge Termination
•·2.9V Trickle Charge Threshold (TP4056)
•·Soft-Start Limits Inrush Current
•·Available Radiator in 8-Lead SOP Package, the Radiator need connect GND or impending

APPLICATIONS
• Cellular Telephones, PDAs, GPS
• Charging Docks and Cradles
• Digital Still Cameras, Portable Devices
• USB Bus-Powered Chargers,Chargers

DESCRIPTION
The PS2715-1 is an optically coupled isolator containing GaAs light emitting diodes and an NPN silicon phototransistor in a plastic SOP for high density applications.
The package is an SOP (Small Outline Package) type for high density mounting applications.

FEATURES
• AC input response
• High current transfer ratio (CTR = 200 % TYP. @ IF = ±1 mA)
• High isolation voltage (BV = 3 750 Vr.m.s.)
• Small and thin package (4-pin SOP)
• Ordering number of tape product: PS2715-1-F3, F4
• UL approved: File No. E72422 (S)

APPLICATIONS
• Programmable logic controllers
• Modem/FAX

Description

The CPC1002N is a miniature 1-Form-A DC solid state relay in a 4-Pin SOP package that employs optically coupled MOSFET technology to provide 1500Vrms of input/output isolation. The super-efficient MOSFET switches and photovoltaic die use Clare’s patented OptoMOS architecture. The optically coupled output is controlled by the input's highly efficient GaAlAs infrared LED. The CPC1002N uses Clare’s state of the art double-molded vertical construction packaging to produce one of the world’s smallest relays. The CPC1002N offers board space savings of at least 20% over the competitor’s larger 4-Pin SOP relay.

Features

• Designed for use in security systems complying with EN50130-4

• Only 2mA of LED current required to operate

• Small 4-Pin SOP Package

• TTL/CMOS Compatible input

• 100% Solid State

• High Reliability

• Arc-Free With No Snubbing Circuits

• 1500Vrms Input/Output Isolation

• No EMI/RFI Generation

• Immune to radiated EM fields

• SMD Pick & Place, Wave Solderable

• Tape & Reel Version Available

Applications

• Security

  • Passive Infrared Detectors (PIR)

  • Data Signalling

  • Sensor Circuitry

• Instrumentation

  • Multiplexers

  • Data Acquisition

  • Electronic Switching

  • I/O Subsystems

• Meters (Watt-Hour, Water, Gas)

• Medical Equipment—Patient/Equipment Isolation

• Aerospace

• Industrial Controls

Description

CPC1009N is a miniature low voltage, low on-resistance, low off-state leakage, 1-Form-A solid state relay in a 4-Pin SOP package.

The MOSFET switches and photovoltaic die use Clare’s patented OptoMOS® architecture to provide 1500 Vrms of input-to-output isolation. The optically coupled output is controlled by a highly efficient GaAIAs infrared LED.

The CPC1009N uses Clare’s state of the art double-molded vertical construction to produce one of the world’s smallest 4-pin relays, which offers board space savings of 20% over the competitor’s larger 4-pin SOP relay.

Features

• Extremely Low Output Leakage

• 1500Vrms Input/Output Isolation

• Small 4-Pin SOP Package

• Low Drive Power Requirements (TTL/CMOS Compatible)

• No Moving Parts

• High Reliability

• Arc-Free With No Snubbing Circuits

• No EMI/RFI Generation

• Machine Insertable, Wave Solderable

• Tape & Reel Version Available

Applications

• Instrumentation

   • Multiplexers

   • Data Acquisition

   • Electronic Switching

   • I/O Subsystems

   • Meters (Watt-Hour, Water, Gas)

• Medical Equipment—Patient/Equipment Isolation

• Security Systems

• Aerospace

• Industrial Controls

Description

The CPC1017N is a miniature 1-Form-A solid state relay in a 4 pin SOP package that employs optically coupled MOSFET technology to provide 1500V of input to output isolation. The super efficient MOSFET switches and photovoltaic die use Clare’s patented OptoMOS architecture. The optically coupled input is controlled by a highly efficient GaAIAs infrared LED. The CPC1017N uses Clare’s state-of-the-art double molded vertical construction packaging to produce the world’s smallest relay. The CPC1017N offers board space savings of at least 20% over the competitor’s larger 4 pin SOP relay. It boasts the industries’ lowest input current to operate in its class.

Features

• Design for use in security systems complying with EN50130-4

• Only 1mA of LED curent required to operate

• Small 4 Pin SOP Package

• TTL/CMOS Compatible input

• No Moving Parts

• High Reliability

• Arc-Free With No Snubbing Circuits

• 1500VRMS Input/Output Isolation/2100V AC peak

• No EMI/RFI Generation

• Immune to radiated EM fields

• SMD Pick & Place, Wave Solderable

• Tape & Reel Version Available

Applications

• Security

   • Passive Infrared Detectors (PIR)

   • Data Signalling

   • Sensor Circuitry

• Instrumentation

   • Multiplexers

   • Data Acquisition

   • Electronic Switching

   • I/O Subsystems

   • Meters (Watt-Hour, Water, Gas)

• Medical Equipment—Patient/Equipment Isolation

• Aerospace

• Industrial Controls