Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Description + Content Search

Search Word's :
Part Name(s) : AD8041-EB
ADI
Analog Devices
Description : 160 MHz Rail-to-Rail Amplifier with Disable

PRODUCT DESCRIPTION
The AD8041 is a low power voltage feedback, high speed Amplifier designed to operate on +3 V, +5 V or ±5 V supplies. It has true single supply capability with an input voltage range extending 200 mV below the negative rail and within 1 V of the positive rail.
The output voltage swing extends to within 50 mV of each rail, providing the maximum output dynamic range. Additionally, it features gain flatness of 0.1 dB to 30 MHz while offering differential gain and phase error of 0.03% and 0.03° on a single +5 V supply. This makes the AD8041 ideal for professional video electronics such as cameras, video switchers or any high speed portable equipment. The AD8041’s low distortion and fast settling make it ideal for buffering high speed A-to-D converters.

FEATURES
  Fully Specified for +3 V, +5 V, and 65 V Supplies
  Output Swings Rail to Rail
  Input Voltage Range Extends 200 mV Below Ground
  No Phase Reversal with Inputs 1 V Beyond Supplies
  Disable/Power-Down Capability
  Low Power of 5.2 mA (26 mW on +5 V)
  High Speed and Fast Settling on +5 V:
     160 MHz –3 dB Bandwidth (G = +1)
     160 V/ms Slew Rate
     30 ns Settling Time to 0.1%
  Good Video Specifications (RL = 150 V, G = +2)
     Gain Flatness of 0.1 dB to 30 MHz
     0.03% Differential Gain Error
     0.038 Differential Phase Error
  Low Distortion
     –69 dBc Worst Harmonic @ 10 MHz
  Outstanding Load Drive Capability
     Drives 50 mA 0.5 V from Supply Rails
  Cap Load Drive of 45 pF
 
APPLICATIONS
  Power Sensitive High Speed Systems
  Video Switchers
  Distribution Amplifiers
  A/D Driver
  Professional Cameras
  CCD Imaging Systems
  Ultrasound Equipment (Multichannel)
  Single-Supply Multiplexer

Description : 3V RAIL TO RAIL CMOS Dual OPERATIONAL Amplifier (WITH STANDBY POSITION)

DESCRIPTION
The TS3V902 is a RAIL TO RAIL Dual CMOS operational Amplifier designed to operate with single or Dual supply voltage.

■ DEDICATED TO 3.3V OR BATTERY SUPPLY (specified at 3V and 5V)
■ RAIL TO RAIL INPUT AND OUTPUT VOLTAGERANGES
■ STANDBY POSITION : REDUCED CONSUMPTION (0.5µA) AND HIGH IMPEDANCE OUTPUTS
■ SINGLE (OR Dual) SUPPLY OPERATION FROM 2.7V TO 16V
■ EXTREMELY LOW INPUT BIAS CURRENT : 1pA TYP
■ SPECIFIED FOR 600Ω AND 100Ω LOADS
■ LOW SUPPLY CURRENT : 200µA/Ampli
■ SPICE MACROMODEL INCLUDED IN THIS SPECIFICATION

Description : 160 MHz Rail-to-Rail Amplifier with Disable

PRODUCT DESCRIPTION
The AD8041 is a low power voltage feedback, high speed Amplifier designed to operate on +3 V, +5 V, or ±5 V supplies. It has true single-supply capability with an input voltage range extending 200 mV below the negative rail and within 1 V of the positive rail.
The output voltage swing extends to within 50 mV of each rail, providing the maximum output dynamic range. Additionally, it features gain flatness of 0.1 dB to 30 MHz while offering differential gain and phase error of 0.03% and 0.03° on a single 5 V supply. This makes the AD8041 ideal for professional video electronics such as cameras, video switchers, or any high speed portable equipment. The AD8041’s low distortion and fast settling make it ideal for buffering high speed A-to-D converters.

FEATURES
  Fully Specified for +3 V, +5 V, and ±5 V Supplies
  Output Swings Rail to Rail
  Input Voltage Range Extends 200 mV Below Ground
  No Phase Reversal with Inputs 1 V Beyond Supplies
  Disable/Power-Down Capability
  Low Power of 5.2 mA (26 mW on 5 V)
  High Speed and Fast Settling on 5 V:
     160 MHz –3 dB Bandwidth (G = +1)
     160 V/μs Slew Rate
     30 ns Settling Time to 0.1%
  Good Video Specifications (RL = 150 Ω, G = +2)
     Gain Flatness of 0.1 dB to 30 MHz
     0.03% Differential Gain Error
     0.03° Differential Phase Error
  Low Distortion
     –69 dBc Worst Harmonic @ 10 MHz
  Outstanding Load Drive Capability
     Drives 50 mA 0.5 V from Supply Rails
  Cap Load Drive of 45 pF

APPLICATIONS
  Power Sensitive High Speed Systems
  Video Switchers
  Distribution Amplifiers
  A/D Drivers
  Professional Cameras
  CCD Imaging Systems
  Ultrasound Equipment (Multichannel)
  Single-Supply Multiplexer

Description : 3V RAIL TO RAIL CMOS Dual OPERATIONAL Amplifier

DESCRIPTION
The TS3V912 is a RAIL TO RAIL CMOS Dual operational Amplifier designed to operate with a single 3V supply voltage.

■ DEDICATED TO 3.3V OR BATTERY SUPPLY (specified at 3V and 5V)
■ RAIL TO RAIL INPUT AND OUTPUT VOLTAGERANGES
■ SINGLE SUPPLY OPERATION FROM 2.7V TO 16V
■ EXTREMELY LOW INPUT BIAS CURRENT : 1pA typ
■ LOW INPUT OFFSET VOLTAGE : 2mV max.
■ SPECIFIED FOR 600Ω AND 100Ω LOADS
■ LOW SUPPLY CURRENT : 200µA/Ampli (VCC = 3V)
■ ESD TOLERANCE : 3KV
■ LATCH-UP IMMUNITY
■ MACROMODEL INCLUDED IN THIS SPECIFICATION

Description : 100 MHz Single Supply Rail to Rail Amplifier

General Description
The EL5144C series Amplifiers are voltage feedback, high speed, rail to rail Amplifiers designed to operate on a single +5V supply. They offer unity gain stability with an unloaded –3dB bandwidth of 100 MHz. The input common mode voltage range extends from the negative rail to within 1.5V of the positive rail. Driving a 75Ω double terminated coaxial cable, the EL5144C series Amplifiers drive to within 150 mV of either rail.

Features
• Rail to Rail Output Swing
• -3 dB Bandwidth = 100 MHz
• Single Supply +5V operation
• Power Down to 2.6 µA
• Large Input Common Mode Range 0V < VCM < 3.5 V
• Diff Gain/Phase = 0.1%/0.1°
• Low Power 35mW per Amplifier
• Space Saving SOT23-5, MSOP- 8&10, & QSOP-16 packaging

Applications
• Video Amplifier
• 5 Volt Analog Signal Processing
• Multiplexer
• Line Driver
• Portable Computers
• High Speed Communications
• Sample & Hold Amplifier
• Comparator

Part Name(s) : AD823AN
ADI
Analog Devices
Description : Dual, 16 MHz, Rail-to-Rail FET Input Amplifier

GENERAL DESCRIPTION
The AD823 is a Dual precision, 16 MHz, JFET input op amp that can operate from a single supply of 3.0 V to 36 V or from Dual supplies of ±1.5 V to ±18 V. It has true single-supply capability with an input voltage range extending below ground in single-supply mode. Output voltage swing extends to within 50 mV of each rail for IOUT ≤ 100 μA, providing outstanding output dynamic range.
An offset voltage of 800 μV maximum, an offset voltage drift of 2 μV/°C, input bias currents below 25 pA, and low input voltage noise provide dc precision with source impedances up to a Gigaohm. It provides 16 MHz, −3 dB bandwidth, −108 dB THD @ 20 kHz, and a 22 V/μs slew rate with a low supply current of 2.6 mA per Amplifier. The AD823 drives up to 500 pF of direct capacitive load as a follower and provides an output current of 15 mA, 0.5 V from the supply rails. This allows the Amplifier to handle a wide range of load conditions.

FEATURES
   Single-supply operation
      Output swings Rail-to-Rail
      Input voltage range extends below ground
      Single-supply capability from 3 V to 36 V
   High load drive
      Capacitive load drive of 500 pF, G = +1
      Output current of 15 mA, 0.5 V from supplies
   Excellent ac performance on 2.6 mA/Amplifier
      −3 dB bandwidth of 16 MHz, G = +1
      350 ns settling time to 0.01% (2 V step)
      Slew rate of 22 V/μs
   Good dc performance
      800 μV maximum input offset voltage
      2 μV/°C offset voltage drift
      25 pA maximum input bias current
   Low distortion: −108 dBc worst harmonic @ 20 kHz
   Low noise: 16 nV/√Hz @ 10 kHz
   No phase inversion with inputs to the supply rails

APPLICATIONS
   Battery-powered precision instrumentation
   Photodiode preamps
   Active filters
   12-bit to 16-bit data acquisition systems
   Medical instrumentation

Description : 100 MHz Single Supply Rail to Rail Amplifier

General Description

The EL5144C series Amplifiers are voltage feedback, high speed, rail to rail Amplifiers designed to operate on a single +5V supply. They offer unity gain stability with an unloaded –3dB bandwidth of 100 MHz. The input common mode voltage range extends from the negative rail to within 1.5V of the positive rail. Driving a 75Ω double terminated coaxial cable, the EL5144C series Amplifiers drive to within 150 mV of either rail. The 200 V/µsec slew rate and 0.1% / 0.1° differential gain / differential phase makes these parts ideal for composite and component video applications. With its voltage feedback architecture, this Amplifier can accept reactive feedback networks, allowing them to be used in analog filtering applications These Amplifiers will source 90 mA and sink 65 mA.



 


Part Name(s) : AD8044AR
ADI
Analog Devices
Description : Quad 150 MHz Rail-to-Rail Amplifier

PRODUCT DESCRIPTION
The AD8044 is a quad, low power, voltage feedback, high speed Amplifier designed to operate on +3 V, +5 V, or ±5 V supplies. It has true single-supply capability with an input voltage range extending 200 mV below the negative rail and within 1 V of the positive rail.
   
FEATURES
    Single AD8041 and Dual AD8042 Also Available
    Fully Specified at +3 V, +5 V, and ±5 V Supplies
    Output Swings to Within 25 mV of Either Rail
    Input Voltage Range Extends 200 mV Below Ground
    No Phase Reversal with Inputs 1 V Beyond Supplies
    Low Power of 2.75 mA/Amplifier
    High Speed and Fast Settling on +5 V
        150 MHz –3 dB Bandwidth (G = +1)
        170 V/s Slew Rate
        40 ns Settling Time to 0.1%
    Good Video Specifications (RL = 150 Ω, G = +2)
        Gain Flatness of 0.1 dB to 12 MHz
        0.06% Differential Gain Error
        0.15° Differential Phase Error
    Low Distortion
        –68 dBc Total Harmonic @ 5 MHz
    Outstanding Load Drive Capability
        Drives 30 mA 0.5 V from Supply Rails
   
APPLICATIONS
    Active Filters
    Video Switchers
    Distribution Amplifiers
    A/D Driver
    Professional Cameras
    CCD Imaging Systems
    Ultrasound Equipment (Multichannel)
   

Description : RAIL TO RAIL CMOS Dual OPERATIONAL Amplifier (WITH STANDBY POSITION)

DESCRIPTION
The TS902 is a RAIL TO RAIL CMOS Dual operational Amplifier designed to operate with a single or Dual supply voltage.
   
■ RAIL TO RAIL INPUT AND OUTPUT VOLTAGE RANGES
■ STANDBY POSITION : REDUCED CONSUMPTION (0.5µA)
    AND HIGH IMPEDANCE OUTPUTS
■ SINGLE (OR Dual) SUPPLY OPERATION
    FROM 2.7V TO 16V
■ EXTREMELY LOW INPUT BIAS CURRENT :
    1pA typ
■ LOW INPUT OFFSET VOLTAGE : 5mV max.
■ SPECIFIED FOR 600Ω AND 100Ω LOADS
■ LOW SUPPLY CURRENT : 200µA/Ampli
    (VCC = 3V)
■ SPICE MACROMODEL INCLUDED IN THISSPECIFICATION
   

Description : 12MHz Rail-to-Rail Input-Output Operational Amplifier

12MHz Rail-to-Rail Input-Output Operational Amplifier

The EL5420T is a low power, high voltage Rail-to-Rail input-output Amplifier. The EL5420T contains four Amplifiers. Each Amplifier exhibits beyond the rail input capability, Rail-to-Rail output capability and is unity gain stable.

Features
• 12MHz (-3dB) Bandwidth
• 4.5V to 19V Maximum Supply Voltage Range
• 12V/µs Slew Rate
• 500µA Supply Current (per Amplifier)
• ±70mA Continuous Output Current
• ±200mA Output Short Circuit Current
• Unity-gain Stable
• Beyond the Rails Input Capability
Rail-to-Rail Output Swing
• Built-in Thermal Protection
• -40°C to +85°C Ambient Temperature Range
• Pb-free (RoHS compliant)

Applications
• TFT-LCD Panels
• VCOM Amplifiers
• Static Gamma Buffers
• Electronics Notebooks
• Electronics Games
• Touch-screen Displays
• Personal Communication Devices
• Personal Digital Assistants (PDA)
• Portable Instrumentation
• Sampling ADC Amplifiers
• Wireless LANs
• Office Automation
• Active Filters
• ADC/DAC Buffer

12345678910 Next



All Rights Reserved© datasheetq.com  [Privacy Policy ] [ Request Datasheet] [Contact Us]