Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Description + Content Search

Search Word's :

Part Name(s) : 78M6618-IMR TERIDIAN
Teridian Semiconductor Corporation
Description : Octal Power and Energy Measurement IC View

DESCRIPTION
The Teridian 78M6618 is a highly integrated IC for independent monitoring and Measurement of up to eight single-phase AC outlets. With multiple host interface options, an integrated LCD driver, and configurable I/Os, the devICe is ideal for metered Power distribution units (PDUs) and rack enclosures for the data center, as well as intelligent Power strips and subpanels in the grid-friendly digital home.
   
FEATURES
● < 0.5% Wh Accuracy Over Wide 2000:1
    Current Range and Over Temperature
● Exceeds IEC 62053/ANSI C12.20 Standards
● Voltage Reference < 40ppm/°C
● 10 Sensor Inputs—V3P3 Referenced
● 21-Bit Delta-Sigma ADC with Independent
    32-Bit Compute Engine (CE)
● 8-Bit MPU (80515), One Clock Cycle per
    Instruction with 4KB MPU XRAM
● 128KB Flash with Security
● Integrated ICE for MPU Debug
● 32kHz Time Base with Hardware Watchdog
    Timer
● UART and High-Speed Slave SPI Host Interface
    Options
● Up to 19 General-Purpose 5V Tolerant I/O Pins
● LCD Driver (Up to 70 Pixels)
● Packaged in a Lead(Pb)-Free/RoHS-Compliant
    (6/6) 68-Pin QFN
● Robust Sub-Metering ApplICation Firmware:
    o True RMS Calculations for Current, Voltage,
        Line Frequency, Real Power, Reactive
        Power, Apparent Power, and Power Factor
    o Accumulated Watt-Hours, Kilowatt-Hours,
        and Cost
    o Intelligent Switch Control at Zero Crossings
    o Digital Temperature Compensation
    o Phase Compensation (15)
    o QuICk Calibration Routines
    o 46-64Hz Line Frequency Range with Same
        Calibration
    o Programmable Alarm Thresholds
    o High-Level UART CommunICation Protocols
    o High-Level SPI CommunICation Protocols
   

Part Name(s) : MB39C811-EVBSK-02 Cypress
Cypress Semiconductor
Description : Energy Harvesting Starter Kit for Buck Power Management IC with Bluetooth® Smart (Low Energy) Beacon View

DESCRIPTION
The MB39C811-EVBSK-02 is an evaluation board that contains Energy Harvesting Power Management IC, MB39C811 (Buck DC/DC converter) with Bluetooth® Smart (Low Energy), whICh can be used in applICation on the Solar and PiezoelectrIC Energy Harvester. The MB39C811 has a wide input range from 4V up to 23V, and the output voltages are selectable from 1.5V to 5V. The board contains a Programmable (applICation block only) Bluetooth® Smart module, Fujitsu Component: MBH7BLZ02-109004, whICh allows BLE (Bluetooth Low Energy) Beacon and wireless data communICations.
   
FEATURES
■ Installed Energy Harvesting Power Management IC: MB39C811
■ Programmable (applICation block only) Bluetooth® Smart Module: MBH7BLZ02-109004 (*1)
■ Transmit BLE Beacon using Solar Energy and Vibration Energy only
■ Transmit about 1 second intervals under 500lx
■ Support a lot of Energy inputs
    - Solar Cell
    - Piezo ElectrIC
    - USB Bus Power
    - Coin Battery (Expandable: For Hybrid)
    - NFC: Near Field CommunICation (Expandable: Power supply only)
    - Commercial Power Supply: AC85~265V (Expandable: Need additional resister)
■ Installed Temperature Sensor
■ Installed USB Serial Converter IC for changing Beacon IDs
■ Attached Solar Cell for Evaluation
■ Attached Case & USB Cable
■ SchematIC, BOM List, Layout Data, Sample Software
■ Installed Expandable Terminal.
    - Reset Button for MCU (Standard mount)
    - JTAG Connector for MCU Program
    - Expandable Sensor Interface (I2C/GPIO)
    - DIPSW (Expandable)
    - LED (Expandable)
■ Small Size PCB: 45mm × 25mm
   
APPLICATIONS
■ Battery-less BLE Beacon
■ AC Power supply BLE Beacon
■ Wireless Sensor node for IoT
■ BEMS/HEMS/FEMS
■ Active RFID
■ Solar Energy Harvesting
■ Wireless Illumination Control
■ Wireless HVAC Sensors
■ Security System
   

Part Name(s) : 78M6618 78M6618-IM 78M6618-PDU-1 78M6618-IM/F 78M6618-IM/F/P 78M6618-IMR/F 78M6618-IMR/F/P TERIDIAN
Teridian Semiconductor Corporation
Description : Octal Power and Energy Measurement IC View

DESCRIPTION
The Teridian 78M6618 is a highly integrated IC for independent monitoring and Measurement of up to eight single-phase AC outlets. With multiple host interface options, an integrated LCD driver, and configurable I/Os, the devICe is ideal for metered Power distribution units (PDUs) and rack enclosures for the data center, as well as intelligent Power strips and subpanels in the grid-friendly digital home.

FEATURES
• < 0.5% Wh Accuracy Over Wide 2000:1 Current Range and Over Temperature
• Exceeds IEC 62053/ANSI C12.20 Standards
• Voltage Reference < 40ppm/°C
• 10 Sensor Inputs—V3P3 Referenced
• 21-Bit Delta-Sigma ADC with Independent 32-Bit Compute Engine (CE)
• 8-Bit MPU (80515), One Clock Cycle per Instruction with 4KB MPU XRAM
• 128KB Flash with Security
• Integrated ICE for MPU Debug
• 32kHz Time Base with Hardware Watchdog Timer
• UART and High-Speed Slave SPI Host Interface Options
• Up to 19 General-Purpose 5V Tolerant I/O Pins
• LCD Driver (Up to 70 Pixels)
• Packaged in a Lead(Pb)-Free/RoHS-Compliant (6/6) 68-Pin QFN
• Robust Sub-Metering ApplICation Firmware:
    o True RMS Calculations for Current, Voltage, Line Frequency, Real Power, Reactive Power, Apparent Power, and Power Factor
    o Accumulated Watt-Hours, Kilowatt-Hours, and Cost
    o Intelligent Switch Control at Zero Crossings
    o Digital Temperature Compensation
    o Phase Compensation (±15°)
    o QuICk Calibration Routines
    o 46-64Hz Line Frequency Range with Same Calibration
    o Programmable Alarm Thresholds
    o High-Level UART CommunICation Protocols
    o High-Level SPI CommunICation Protocols

Part Name(s) : SA9105A SA9105AFA SA9105APA Sames
South African Micro Electronic Systems
Description : THREE PHASE UNIDIRECTIONAL Power/Energy METERING IC WITH PULSE OUTPUT View

DESCRIPTION

The SAMES SA9105A Three Phase unidirectional Power/Energy metering integrated circuit generates a pulse rate output, the frequency of whICh is proportional to the Power consumption. The SA9105A performs the calculations of active Power. The method of calculation takes the Power factor into account.

Energy consumption is determined by the Power Measurement being integrated over time.

The output of this innovative universal three phase Power/Energy metering integrated circuit, is ideally suited for applICations such as residential and industrial Energy metering and control.



FEATURES

■ Performs unidirectional one, two or three phase Power and Energy Measurement

■ Meets the IEC 521/1036 SpecifICation requirements for Class 1 AC Watt hour meters

■ Operates over a wide temperature Range

■ Uses current transformers for current sensing

■ Excellent long term stability

■ Easily adaptable to different signal levels

■ Precision voltage reference on-chip

■ Three pulse rate outputs available

■ Protected against ESD



 



Part Name(s) : SA9102F SA9102FPA SA9102FSA SA9102H SA9102HPA SA9102HSA Sames
South African Micro Electronic Systems
Description : SINGLE PHASE BIDIRECTIONAL Power/Energy METERING IC WITH INSTANTANEOUS PULSE OUTPUT View

DESCRIPTION

The SAMES SA9102F and SA9102H Single Phase bidirectional Power/Energy metering integrated circuits generate pulse rate outputs for positive and negative Energy directions, the frequency of whICh is proportional to the Power consumption. These devICes perform the calculation for active Power.

The method of calculation takes the Power factor into account.

Energy consumption is determined by the Power Measurement being integrated over time.



FEATURES

■ Performs bidirectional Power and Energy Measurement

■ Meets the IEC 521/1036 SpecifICation requirements for Class 1 AC Watt hour meters

■ Protected against ESD

Power consumption rating typICally 25mW

■ Adaptable to different types of current sensors

■ Operates over a wide temperature range

■ Precision voltage reference on-chip

■ Two output signal formats available



 


Part Name(s) : SA9102C SA9102CPA SA9102CSA Sames
South African Micro Electronic Systems
Description : SINGLE PHASE UNIDIRECTIONAL Power/Energy METERING IC PULSE OUTPUT View

DESCRIPTION

The SAMES SA9102C Single Phase unidirectional Power/Energy metering integrated circuit generates a pulse rate output, the frequency of whICh is proportional to the Power consumption. The SA9102C performs the calculation for active Power.

This method of calculation takes the Power factor into account.

Energy consumption is determined by the Power Measurement being integrated over time.



FEATURES

■ Performs unidirectional Power and Energy Measurement

■ Meets the IEC 521/1036 SpecifICation requirements for Class 1 AC Watt hour meters

■ Protected against ESD

■ Total Power consumption rating typICally 25mW

■ Adaptable to different types of current sensors

■ Operates over a wide temperature range

■ Precision voltage reference on-chip

■ Different pulse rate options available



 


Part Name(s) : 78M6612 78M6612-IGT 78M6612-IGT/F 78M6612-IGT/F/P 78M6612-IGTR 78M6612-IGTR/F 78M6612-IGTR/F/P 78M6612-IM 78M6612-IM/F 78M6612-IM/F/P TERIDIAN
Teridian Semiconductor Corporation
Description : Single-Phase, Dual-Outlet Power and Energy Measurement IC View

DESCRIPTION
The Teridian 78M6612 is a highly integrated, single-phase, Power and Energy Measurement and monitoring SOC whICh includes a 32-bit compute engine (CE), an MPU core, RTC, and Flash. The Teridian patented Single Converter Technology® with a 22-bit delta-sigma ADC, 4 analog inputs, digital temperature compensation, and precision voltage reference supports a wide range of single-phase, dual-outlet Power Measurement applICations with very few external components.
   
FEATURES
• Measures each outlet of a duplex receptacle with a
    single IC
• Provides complete Energy Measurement and
    communICation protocol capability in a single IC
• Intelligent switch control capability
• < 0.5% Wh accuracy over 2000:1 current range
    and over temperature
• Exceeds IEC62053 / ANSIC12.20 standards
• Voltage reference < 40 ppm/°C
• Four sensor inputs – VDD referenced
• Low jitter Wh and VARh pulse test outputs (10 kHz
    maximum)
• Pulse count for pulse outputs
• Line frequency count for RTC
• Digital temperature compensation
• Sag detection for phase A and B
• Independent 32-bit compute engine
• 46-64 Hz line frequency range with same
    calibration
• Phase compensation (±7°)
• Battery backup for RTC and battery monitor
• Three battery modes with wake-up timer:
    Brownout mode (48 µA)
    LCD mode (5.7 µA)
    Sleep mode (2.9 µA)
Energy display on main Power failure
• Wake-up timer
• 22-bit delta-sigma ADC
• 8-bit MPU (80515), 1 clock cycle per instruction w/
    integrated ICE for MPU debug
• RTC with temperature compensation
• Auto-Calibration
• Hardware watchdog timer, Power fail monitor
• LCD driver (up to 152 pixels)
• Up to 18 general purpose I/O pins
• 32 kHz time base
• 32 KB Flash with security
• 2 KB MPU XRAM
• Two UARTs
• Digital I/O pins compatible with 5 V inputs
• 64-pin LQFP or 68-pin QFN package
• RoHS compliant (6/6) lead-free packages
• Complete ApplICation Firmware available
   

Part Name(s) : SA9904A SA9904APA SA9904ASA Sames
South African Micro Electronic Systems
Description : Three Phase Power / Energy IC with SPI Interface View

DESCRIPTION

The SAMES SA9904A is a three phase bi-directional Energy/Power metering integrated circuit that performs Measurement of active and reactive Power, mains voltage and mains frequency.

The SA9904A is pin compatible to the SA9604A. New features include, RMS mains voltage and accurate reactive Power Measurements.

Measured values for active and reactive Energy, the mains voltage and frequency for each phase are accessible through a SPI bus from 24 bit registers.



FEATURES

■ Bi-directional active and reactive Power/Energy Measurement

■ RMS Voltage and frequency Measurement

■ Individual Phase information

■ SPI communICation bus

■ Meets the IEC 521/1036 SpecifICation requirements for Class 1 AC Watt hour meters

■ Meets the IEC 1268 SpecifICation requirements for VAR hour meters

■ Protected against ESD

■ Total Power consumption rating below 60mW

■ Uses current transformers for current sensing

■ Operates over a wide temperature range

■ Precision voltage reference on-chip



 


Part Name(s) : SA2007H SA2007HPA SA2007HSA Sames
South African Micro Electronic Systems
Description : Single Phase Bidirectional Dual Element Power/Energy Metering IC with Pulse Output View

DESCRIPTION
The SAMES SA2007H is a single phase bidirectional dual element Energy metering integrated circuit. It provides a simple analog interface to a mICro-controller and is specifICally designed for meter manufacturers to have full control over the meter functionality.
The SA2007H has two current sensor inputs. The Power consumption on both inputs are continuously measured. A typICal applICation would be to monitor Live and Neutral lines for tamper detection.
For each current sensor input the SA2007H integrated circuit has a corresponding pulse output, each generating a pulse rate with a frequency proportional to the Power consumption measured on the specifIC channel.
The SA2007H performs active Power Measurement and takes the Power factor into account. Energy consumption can be determined by the Power Measurement being integrated over time. The Energy flow direction information is also available for each channel.

FEATURES
■ Two current sensor inputs
■ Dual pulse and Energy direction outputs
■ No external crystal or resonator required
■ Performs bi-directional Power and Energy Measurement
■ Meets the IEC 521/1036 SpecifICation for Class 1 AC Watt hour meters
■ Protected against ESD
■ Total Power consumption rating below 25mW
■ Adaptable to different types of sensors
■ Operates over a wide temperature range
■ Precision voltage reference on-chip

12345678910 Next



All Rights Reserved© datasheetq.com 2015 - 2020  [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]