Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Description + Content Search

Search Word's :
Part Name(s) : SCA1000-D01
Murata
Murata Manufacturing
Description : PRODUCT SPECIFICATION FOR XY-DUAL AXIS ACCELEROMETER

General description

The SCA1000 ACCELEROMETER consists of two silicon bulk micro machined sensing element chips and a signal conditioning ASIC. The chips aremounted on a pre-molded package and wire bonded to appropriate contacts. The sensing elements and ASIC are protected with silicone gel and lid. The sensor has 12 SMD legs (Gull-wing type).



SCA1000 family ACCELEROMETER Features

• Single +5V supply

• Two ratiometric analog outputs in relation to supply voltage (Vdd = 4.75....5.25V)

•Wide load driving capability

• Serial Peripheral Interface (SPI) compatible

•Provides digital output FOR both channels

•Supports testing and programming

• Non-volatile programming features

•Factory programmable filter settings ( 400Hz, 1 kHz, WB, Ext_C )

•Offset and sensitivity calibration

•Linear temperature compensation

• Enhanced failure detection features

•True self test by deflecting the sensing elements’proof mass by electrostatic FORce. Deflection voltage is adjustable with two memory bits FOR both channels. The self-test is channel specific, and separately activated FOR both channels by digital on-off commands via dedicated pins or via SPI bus.

•Continuous sensing element interconnection failurecheck

 


ADI
Analog Devices
Description : Precision, ±5 g, Dual-AXIS, High Temperature iMEMS ACCELEROMETER

GENERAL DESCRIPTION
The ADXL206 is a precision, low power, complete dual-AXIS iMEMS® ACCELEROMETER FOR use in high temperature environments. The ACCELEROMETER integrates the sensor with signal conditioned voltage outputs on a single, monolithic IC.

FEATURES
   High perFORmance, dual-AXIS ACCELEROMETER
      on a single IC
   −40°C to +175°C ambient temperature range
   Long life: guaranteed 1000 hours at TA = 175°C
   13 mm × 8 mm × 2 mm side-brazed ceramic dual in-line
      package
   1 mg resolution at 60 Hz
   Low power: 700 μA at VS = 5 V (typical)
   High zero g bias repeatability
   High sensitivity accuracy
   Bandwidth adjustment with a single capacitor
   Single-supply operation
   RoHS-compliant
   Compatible with Sn/Pb and Pb-free solder processes

APPLICATIONS
   Geological exploration tilt and vibration measurement
   Extreme high temperature industrial PRODUCTs

Part Name(s) : ADXL202EB
ADI
Analog Devices
Description : Dual AXIS ACCELEROMETER Evaluation Board

GENERAL DESCRIPTION
The ADXL202EB is a simple evaluation board that allows the user to quickly evaluate the perFORmance of the ADXL202 dual AXIS ± 2 g ACCELEROMETER. Only three additional through-hole passive components must be added, depending on the bandwidth required in your application. The ADXL202EB has a 5-pin 0.1-inch spaced header FOR access to all power and signal lines that may be attached to a prototyping board (breadboard) or wired via a standard plug. Two holes are provided FOR mechanical attachment of the ADXL202EB to your application.

CIRCUIT DESCRIPTION
The schematic and parts list of the ADXL202EB are shown in Figure 1 and Table I respectively. The minimal application will require at least one resistor (RSET) added to the board to set the PWM period (T2). Analog bandwidth may be set by adding capacitors C2 and C3. Refer to the ADXL202 data sheet FOR a complete description of the operation of the ACCELEROMETER.

ADI
Analog Devices
Description : Programmable Dual-AXIS Inclinometer/ACCELEROMETER

GENERAL DESCRIPTION

The ADIS16201 is a complete, dual-AXIS acceleration and inclination angle measurement system available in a single compact package enabled by the Analog Devices iSensor™ integration. By enhancing the Analog Devices iMEMS® sensor technology with an embedded signal processing solution, the ADIS16201 provides factory calibrated and tunable digital sensor data in a convenient FORmat that can be accessed using a serial peripheral interface (SPI). The SPI interface provides access to measurements FOR dual-AXIS linear acceleration, dual AXIS linear inclination angle, temperature, power supply, and one auxiliary analog input. Easy access to calibrated digital

sensor data provides developers with a system-ready device, reducing development time, cost, and program risk.



FEATURES

Dual-AXIS inclinometer/ACCELEROMETER measurements

12-, 14-bit digital inclination/acceleration sensor outputs

±1.7 g ACCELEROMETER measurement range

±90° inclinometer measurement range, linear output

12-bit digital temperature sensor output

Digitally controlled sensitivity and bias calibration

Digitally controlled sample rate

Digitally controlled frequency response

Dual alarm settings with rate/threshold limits

Auxiliary digital I/O

Digitally activated self test

Digitally activated low power mode

SPI®-compatible serial interface

Auxiliary 12-bit ADC input and DAC output

Single-supply operation: 3.0 V to +3.6 V

3500 g powered shock survivability



APPLICATIONS

PlatFORm control, stabilization, and leveling

Tilt sensing, inclinometers

Motion/position measurement

Monitor/alarm devices (security, medical, safety)



 


ADI
Analog Devices
Description : Precision ±1.7 g Single-/Dual-AXIS iMEMS® ACCELEROMETER

GENERAL DESCRIPTION

The ADXL204 is a high precision, low power, complete dual AXIS ACCELEROMETER with signal-conditioned voltage outputs, all on a single monolithic IC. Like the ADXL203, it measures acceleration with a full-scale range of ±1.7 g; however, the ADXL204 is tested and specified FOR 3.3 V supply voltage, whereas the ADXL203 is tested and specified at 5 V. Both parts function well over a wide 3 V to 6 V operating voltage range. The ADXL204 can measure both dynamic acceleration (FOR example, vibration) and static acceleration (FOR example, gravity).



FEATURES

  High perFORmance, dual-AXIS ACCELEROMETER on a single IC chip

  Specified at VS = 3.3 V

  5 mm × 5 mm × 2 mm LCC package

  Better than 2 mg resolution at 60 Hz

  Low power: 500 μA at VS = 3.3 V (typical)

  High zero g bias stability

  High sensitivity accuracy

  –40°C to +125°C temperature range

  X-AXIS and Y-AXIS aligned to within 0.1° (typical)

  BW adjustment with a single capacitor

  Single-supply operation

  3500 g shock survival

  RoHS compliant

  Compatible with Sn/Pb- and Pb-free solder processes



 

APPLICATIONS

  Vehicle dynamic control (VDC)/electronic stability program (ESP) systems

  Electronic chassis controls

  Electronic braking

  PlatFORm stabilization/leveling

  Navigation

  Alarms and motion detectors

  High accuracy, 2-AXIS tilt sensing



 


Part Name(s) : MXR7311GL
ETC
Unspecified
Description : Low Cost, Low Noise ±2 g Dual AXIS ACCELEROMETER with Ratiometric Analog Outputs

[MEMSIC]

GENERAL DESCRIPTION
The MXR7311GL is a low cost, dual AXIS ACCELEROMETER fabricated on a standard, submicron CMOS process. It is a complete sensing system with on-chip mixed signal processing. The MXR7311GL measures acceleration with a full-scale range of ±2 g and a sensitivity of 167mV/g @3V.

FEATURES
    Low cost
    Resolution better than 1 milli-g
    Dual AXIS ACCELEROMETER fabricated on a monolithic
    CMOS IC
    On chip mixed signal processing
    No moving parts; >50,000 g shock survival rating
    5mm X 5mm X 2mm LCC package
    2.7V to 5.25V single supply continuous operation
    Compensated FOR Sensitivity over temperature
    Ultra low initial Zero-g Offset
    No adjustment needed outside

APPLICATIONS
    Tilt and motion sensing in cost-sensitive applications
    Smart handheld devices
    Computer security
    Input devices
    Pedometers and activity monitors
    Gaming controllers
    Toys and entertainment PRODUCTs

Description : Dual-AXIS ±1.7 g ACCELEROMETER with SPI Interface

GENERAL DESCRIPTION
The ADIS16003 is a low cost, low power, complete dual-AXIS ACCELEROMETER with an integrated serial peripheral interface (SPI). An integrated temperature sensor is also available on the SPI interface. The ADIS16003 measures acceleration with a full-scale range of ±1.7 g (minimum), and it can measure both dynamic acceleration (vibration) and static acceleration (gravity).

FEATURES
   Dual-AXIS ACCELEROMETER
   SPI® digital output interface
   Internal temperature sensor
   Highly integrated; minimal external components;
      bandwidth externally selectable
   1 mg resolution at 60 Hz
   Externally controlled electrostatic self-test
   3.0 V to 5.25 V single-supply operation
   Low power: <2 mA
   3500 g shock survival
   7.2 mm × 7.2 mm × 3.6 mm package

APPLICATIONS
   Industrial vibration/motion sensing
   PlatFORm stabilization
   Dual-AXIS tilt sensing
   Tracking, recording, analysis devices
   Alarms, security devices

Description : Low Cost ±1.2 g Dual AXIS ACCELEROMETER

GENERAL DESCRIPTION

The ADXL213 is a low cost, low power, complete dual AXIS ACCELEROMETER with signal conditioned, duty cycle modulated outputs, all on a single monolithic IC. The ADXL213 measures acceleration with a full-scale range of ±1.2 g (typical). The ADXL213 can measure both dynamic acceleration (e.g., vibration) and static acceleration (e.g., gravity).



FEATURES

Dual AXIS ACCELEROMETER on a single IC chip

5 mm × 5 mm × 2 mm LCC package

1 mg resolution at 60 Hz

Low power: 700 µA at VS = 5 V (typical)

High zero g bias stability

High sensitivity accuracy

Pulse width modulated digital outputs

X and Y axes aligned to within 0.1° (typical)

BW adjustment with a single capacitor

Single-supply operation

3500 g shock survival



APPLICATIONS

Automotive tilt alarms

Data projectors

Navigation

PlatFORm stabilization/leveling

Alarms and motion detectors

High accuracy, 2-AXIS tilt sensing



 


ADI
Analog Devices
Description : Low Cost, Ultracompact ±2 gDual-AXIS ACCELEROMETER

GENERAL DESCRIPTION

The ADXL311 is a low cost,low power,completedual-AXIS ACCELEROMETER withsignal conditionedvoltage outputs, all on a single monolithic IC.The ADXL311 is built using the same proven iMEMS® process used in over 100 million Analog Devices ACCELEROMETERs shipped todate,with demonstrated 1 FIT reliability (1 failure per 1 billion deviceoperating hours).



FEATURES

Low cost

High resolution

Dual-AXIS ACCELEROMETER on a single IC chip

5 mm × 5 mm × 2 mm CLCC package

Low power < 400 µA (typ)

X-AXIS and Y-AXIS aligned to within 0.1° (typ)

BW adjustment with a single capacitor

Single-supply operation

High shock survival



APPLICATIONS

Tilt and motion sensing in cost-sensitive applications

Smart handheld devices

Computer security

Input devices

Pedometers and activitymonitors

Game controllers

Toys and entertainment PRODUCTs


Part Name(s) : ADXL288
ADI
Analog Devices
Description : High PerFORmance, Dual-AXIS Digital Output ACCELEROMETER

GENERAL DESCRIPTION

The ADXL288 is a dual-AXIS ACCELEROMETER with signal conditioned outputs available via a 16-bit SPI interface. Identical, independent X and Y sense structures are implemented to create a high perFORmance, high integrity acceleration sensing system. The X and Y acceleration channels have a nominal full-scale range of ±120 g and a bandwidth of 408 Hz. The acceleration data is provided as a 12-bit, twos complement word with a resolution of 62.5 mg/LSB.



FEATURES

±120 g full-scale range

  12-bit resolution at 62.5 mg/LSB

  512 kHz data interpolation rate

Sensor frequency response down to dc

On-demand electromechanical self-test

Fully differential circuitry FOR high resistance to EMI/RFI

 Independent x- and y-AXIS sense structures FOR robust FMEA perFORmance

Independent x- and y-AXIS arming thresholds

Low noise: 1 LSB rms typical

Qualified FOR automotive applications

Temperature range: −40°C to +105°C

3.3 V and 5 V operation



APPLICATIONS

Impact sensing

Shock detection


12345678910 Next



All Rights Reserved© datasheetq.com  [Privacy Policy ] [ Request Datasheet] [Contact Us]