Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Description + Content Search

Search Word's :
Description : DC-DC CONVERTER REGULATED 5V CHARGE PUMP

Description
The ST619LB is a step-up CHARGE PUMP DC-DC CONVERTER which delivers a REGULATED 5 V ±4 % output at 30 mA and over temperature. The input voltage range is 2 V to 3.6 V (two battery cells).
It requires only four external capacitor: two 0.22 µF flying capacitors, and 10 µF capacitors at the input and output.

Features
REGULATED 5 V ±4 % CHARGE PUMP
■ Output current guaranteed over temperature: 20 mA (VI ≥ 2 V), 30 mA (VI ≥ 3 V)
■ No inductors; very low EMI noise
■ Uses small, inexpensive capacitors
■ Logic controlled 1 µA max shut-down supply current
■ Shut down disconnects load from input
■ Available in SO-8 and DIP-8 packages

Description : REGULATED 5V CHARGE-PUMP DC-DC CONVERTER

General Description
The MAX619 step-up CHARGE-PUMP DC-DC CONVERTER delivers a REGULATED 5V ±4% output at 50mA over temperature. The input voltage range is 2V to 3.6V (two battery cells).
The complete MAX619 circuit fits into less than 0.1in2 of board space because it requires only four external capacitors: two 0.22µF flying capacitors, and 10µF capacitors at the input and output.
Low operating supply current (150µA max) and low shutdown supply current (1µA max) make this device ideal for small, portable, and battery-powered applications. When shut down, the load is disconnected from the input.
The MAX619 is available in 8-pin DIP and SO packages.

Features
REGULATED 5V ±4% CHARGE PUMP
♦ Output Current Guaranteed over Temperature
   20mA (VIN ≥ 2V)
   50mA (VIN ≥ 3V)
♦ 2V to 3.6V Input Range
♦ No Inductors; Very Low EMI Noise
♦ Ultra-Small Application Circuit (0.1in2)
♦ Uses Small, Inexpensive Capacitors
♦ 500kHz Internal Oscillator
♦ Logic-Controlled 1µA Max Shutdown Supply Current
♦ Shutdown Disconnects Load from Input
♦ 8-Pin DIP and SO Packages

Applications
   Two Battery Cells to 5V Conversion
   Local 3V-to-5V Conversion
   Portable Instruments & Handy-Terminals
   Battery-Powered Microprocessor-Based Systems
   5V Flash Memory Programmer
   Minimum Component DC-DC CONVERTERs
   Remote Data-Acquisition Systems
   Compact 5V Op-Amp Supply
   REGULATED 5V Supply from Lithium Backup Battery
   Switching Drive Voltage for MOSFETs in Low-Voltage Systems

Linear
Linear Technology
Description : Low Noise, REGULATED CHARGE PUMP DC/DC CONVERTERs

DESCRIPTION

The LTC®3200/LTC3200-5 are low noise, constant frequency switched capacitor voltage doublers. They produce a REGULATED output voltage from a 2.7V to 4.5V input with up to 100mA of output current. Low external parts count (one flying capacitor and two small bypass capacitors at VIN and VOUT) make the LTC3200/LTC3200-5 ideally suited for small, battery-powered applications.



FEATURES

■ Low Noise Constant Frequency Operation

■ Output Current: 100mA

■ Available in 8-Pin MSOP (LTC3200) and Low Profile (1mm) 6-Pin ThinSOTTM (LTC3200-5) Packages

■ 2MHz Switching Frequency

■ Fixed 5V ±4% Output (LTC3200-5) or ADJ

■ VIN Range: 2.7V to 4.5V

■ Automatic Soft-Start Reduces Inrush Current

■ No Inductors

■ ICC<1µA in Shutdown



APPLICATION

■ White LED Backlighting

■ Li-Ion Battery Backup Supplies

■ Local 3V to 5V Conversion

■ Smart Card Readers

■ PCMCIA Local 5V Supplies



 


Part Name(s) : MAX1747 MAX1747EUP
MaximIC
Maxim Integrated
Description : Triple CHARGE-PUMP TFT LCD DC-DC CONVERTER

General Description
The MAX1747 triple CHARGE-PUMP DC-DC CONVERTER provides the REGULATED voltages required by active matrix thin-film transistor (TFT) liquid-crystal displays (LCDs) in a low-profile TSSOP package. One high power and two low-power CHARGE PUMPs convert the +2.7V to +4.5V input supply voltage into three independent output voltages.
The primary high-power CHARGE PUMP generates an output voltage (VOUT) between 4.5V and 5.5V that is REGULATED within ±1%. The low-power BiCMOS control circuitry and the low on-resistance (RON) power MOSFETs maximize efficiency. The adjustable switching frequency (200kHz to 2MHz) provides fast transient response and allows the use of small low-profile ceramic capacitors.

Features
♦ Adjustable Outputs
   Up to +5.5V Main High-Power Output
   Up to +35V Positive CHARGE-PUMP Output
   Down to -35V Negative CHARGE-PUMP Output
♦ 200kHz to 2MHz Adjustable Switching Frequency
♦ +2.7V to +4.5V Input Supply
♦ Internal Power MOSFETs
♦ 0.1µA Shutdown Current
♦ Internal Soft-Start
♦ Power-Ready Output
♦ Internal Supply Sequencing
♦ Fast Transient Response
♦ Ultra-Thin Solution (No Inductors)
♦ Thin TSSOP Package (1.1mm max)

Applications
   TFT Active-Matrix LCDs
   Passive-Matrix Displays
   Personal Digital Assistants (PDAs)

Description : ULTRA-LOW VOLTAGE OPERATION CHARGE PUMP IC FOR STEP-UP DC-DC CONVERTER STARTUP

ULTRA-LOW VOLTAGE OPERATION CHARGE PUMP IC FOR STEP-UP DC-DC CONVERTER STARTUP

The S-882Z Series is a CHARGE PUMP IC for step-up DC-DC CONVERTER startup, which differs from conventional CHARGE PUMP ICs, in that it uses fully depleted SOI (Silicon on Insulator) technology to enable ultra-low voltage operation.
Being capable of stepping up an extremely low input voltage of 0.3 to 0.35 V, this series enables the efficient use of very low energy levels. The stepped up electric power is stored in a startup capacitor, and it is disCHARGEd as the startup power of the step-up DC-DC CONVERTER when the startup capacitor reaches the disCHARGE start voltage level.

Features
• Operating input voltage 0.3 to 3.0 V
• Current consumption During operation : 0.5 mA max. (at VIN = 0.3 V)
                                     During shutdown : 0.6 µA max. (at VIN = 0.3 V)
• DisCHARGE start voltage 1.8 to 2.4 V (selectable in 0.2 V steps)
• Shutdown voltage DisCHARGE start voltage + 0.1 V (fixed)
• Oscillation frequency 350 kHz typ. (at VIN = 0.3 V)
• Small package SOT-23-5 package
• External component Startup capacitor (CCPOUT), 1 unit*1
• Lead-free products

Applications
• Stepping up from low-voltage power supply such as solar cell and fuel cell
• Stepping up internal power supply voltage of RF tag
• Intermittent power supply to intermittently operating system

Part Name(s) : MAX1673 MAX1673ESA
MaximIC
Maxim Integrated
Description : REGULATED, 125mA-Output, CHARGE-PUMP DC-DC Inverter

General Description
The MAX1673 CHARGE-PUMP inverter provides a low cost, compact means of generating a REGULATED negative output from a positive input at up to 125mA. It requires only three small capacitors, and only two resistors to set its output voltage. The input range is 2V to 5.5V. The REGULATED output can be set from 0V to -VIN in Skip regulation mode or -1.5V to -VIN in Linear (LIN) regulation mode.

Features
REGULATED Negative Output Voltage (up to -1 x VIN)
♦ 125mA Output Current
♦ 35µA Quiescent Supply Current (Skip-mode regulation)
♦ 350kHz Fixed-Frequency, LOW-NOISE Output (Linear-mode regulation)
♦ 2V to 5.5V Input Range
♦ 1µA Logic-Controlled Shutdown

Applications
    Hard Disk Drives
    Measurement Instruments
    Camcorders
    Modems
    Analog Signal-Processing  Applications
    Digital Cameras
   

Description : Single Cell to 3.3V REGULATED CHARGE PUMP DC/DC CONVERTER

DESCRIPTION
The LTC®1502-3.3 is a quadrupler CHARGE PUMP DC/DC CONVERTER that produces a REGULATED 3.3V output from a single alkaline cell input. It requires only five small external capacitors—no inductors are required. Low supply current (40µA typical, 5µA in shutdown) and minimal external components make the LTC1502-3.3 ideal for space and power conscious single-cell applications. The total printed circuit board area of the circuit shown below is less than 0.125in2.

FEATURES
■ Input Voltage Range: 0.9V to 1.8V
■ 0.9V Guaranteed Start-Up Voltage
REGULATED Output Voltage: 3.3V ±4%
■ Output Current: 10mA (VIN ≥ 1V)
■ No Inductors
■ Shutdown Disconnects Load from VIN
■ Low Operating Current: 40µA
■ Low Shutdown Current: 5µA
■ Short-Circuit and Overtemperature Protected
■ Application Circuit Fits in <0.125in2 PCB Area
■ Available in 8-Pin MSOP and SO Packages

APPLICATIONS
■ Pagers
■ Battery Backup Supplies
■ Portable Electronic Equipment
■ Handheld Medical Instruments
■ Glucose Meters

MAS-Oy
Micro Analog Systems Oy
Description : REGULATED CHARGE PUMP DC/DC CONVERTER

DESCRIPTION
MAS9251 is a low noise, constant frequency switched capacitor voltage doubler with REGULATED output. In the adjustable output version an external feedback pin allows the output voltage to be adjusted.
The high switching frequency of MAS9251 guarantees low output ripple even with small ceramic capacitors. The shutdown control pin can be used to turn off the device for power saving. MAS9251 is equipped with soft-start feature, which reduces the circuit’s disturbance to power supply lines during start-up by limiting the maximum input current.

FEATURES
• Two versions:
    Adjustable Output
    Fixed 5 V Output
• Solution without Inductors
• Soft-Start
• Output Accuracy < ± 4%
• Low External Part Count
• Low Noise
• Input Voltage Range: 2.7 V… 4.5 V
• Shutdown Control
• 1 MHz Switching Frequency
• Internal Thermal Shutdown
• Short Circuit Protection
• MSOP-8 and CSP Packages

APPLICATIONS
• LED Backlighting
• White LED Driver
• LED Brightness Control
• Li-Ion Battery Backup Supplies
• Local 3 V to 5 V Conversion
• Smart Card Readers
• PCMCIA Local 5 V Supplies

Description : REGULATED CHARGE PUMP DC/DC CONVERTER

[MAS-Oy]

DESCRIPTION
MAS9251 is a low noise, constant frequency switched capacitor voltage doubler with REGULATED output. In the adjustable output version an external feedback pin allows the output voltage to be adjusted.
The high switching frequency of MAS9251 guarantees low output ripple even with small ceramic capacitors. The shutdown control pin can be used to turn off the device for power saving. MAS9251 is equipped with soft-start feature, which reduces the circuit’s disturbance to power supply lines during start-up by limiting the maximum input current.

FEATURES
• Two versions:
    Adjustable Output
    Fixed 5 V Output
• Solution without Inductors
• Soft-Start
• Output Accuracy < ± 4%
• Low External Part Count
• Low Noise
• Input Voltage Range: 2.7 V… 4.5 V
• Shutdown Control
• 1 MHz Switching Frequency
• Internal Thermal Shutdown
• Short Circuit Protection
• MSOP-8 and CSP Packages

APPLICATIONS
• LED Backlighting
• White LED Driver
• LED Brightness Control
• Li-Ion Battery Backup Supplies
• Local 3 V to 5 V Conversion
• Smart Card Readers
• PCMCIA Local 5 V Supplies

AAT
Advanced Analog Technology, Inc.
Description : REGULATED CHARGE PUMP DC/DC CONVERTERS

GENERAL DESCRIPTION
The AAT1501/A is a CHARGE PUMP DC/DC CONVERTER mainly used for white LED backlighting. It operates with an input voltage ranging from 2.7V to 5.0V to generate constant 5.0V (AAT1501) or 4.5V (AAT1501A) output. The REGULATED output is produced by using an internal feedback switched capacitor voltage doublers.
   
FEATURES
● Monitored Output Voltage
    (AAT1501: % VO = 5V ± 4 %)
    (AAT1501A: % VO = 5.4 V ± 4 %)
● Output Current: 120mA ( VDD = 3.3V)
                             150mA ( VDD = 3.6V)
● Input Voltage Range: 2.7V to 5.0V
● A Power-Saving Shutdown Current of less than
    1µA
● Internal Oscillation Frequency : 750kHz
● Compact SOT-23-6 Package
   

12345678910 Next



All Rights Reserved© datasheetq.com  [Privacy Policy ] [ Request Datasheet] [Contact Us]