Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P/N + Description + Content Search

Search Word's :

EFC SERIES 1313 are metallized polyester capacitors. This SERIES offers the advantage of small size, self healing and low cost. Suggested applications include: medical electronics, telecommunications and high voltage power supplies. Packaging options include: wrap and fill (TF, TC), raDIA. lead box (EFR), axial lead (EC, EF). Application options include: high voltage (HV), "AC" across the line (AC), noise suppression (RC) and switching power supply (SP).
    - 55 °C to + 85 °C at rated voltage.
    To 125 °C at 50% derating.
    Capacitors < 1.0 MFD shall be measured
    at 1 KHz + 20 HZ. Capacitors >1.0 MFD
    shall be measured at 120 HZ. Measurements
    shall be taken at 25 °C.
    At 25 °C, 150% of rated voltage when applied
    TERMINAL to TERMINAL FOR one minute through a
    current limiting resistance.
    At 25 °C after 2 minutes charge time at rated voltage
    or 500 VDC, whichever is less, the minimum IR shall
    be 30,000 Megohm-Microfarad, but need not exceed
    50,000 Megohms FOR voltages greater than 50 VDC,
    and 15,000 Megohm-Microfarads, but need not exceed
    30,000 Megohms FOR 50 VDC or less.
    SERIES 1313 shall meet the requirements
    of MIL-STD. 202C, Method 103B.
    Shall be 1.0 % max. when measured as in Par. 2.
    Will withstand the application of 150% rated voltage at +125 °C FOR 250 hours
    with not more than one failure in 12 permitted.




EFC SERIES MF1206 are polypropylene capacitors with an internal SERIES construction of double-sided metallized carrier and foil contact plates. This SERIES offers the advantages of a self-healing metallized dielectric and the high current/pulsing capabilities (see dv/dt Table) of a foil capacitor. Packaging options include: wrap and fill (TC, TF), raDIA. lead box (EFR), and raDIA. lead dip (DFR).

Description : Surface Mount TRANSZORB® Transient Voltage Suppressors

• Low profile package
• Ideal FOR automated placement
• Glass passivated chip junction
• Available in uni-directional and bi-directional
• 1500 W peak pulse power capability with a 10/1000 μs waveFORm
• Excellent clamping capability
• Low inductance
• Meets MSL level 1, per J-STD-020, LF maximum peak of 260 °C
• AEC-Q101 qualified
• Material categorization: FOR definitions of compliance please see www.vishay.com/doc?99912

  USE in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units FOR consumer, computer, industrial, automotive, and telecommunication.

Description : 0.5mm Pitch SMT Board to Board Connector

■ Features
1. Broad Variations of Stacking Height
    In addition to 0.5mm pitch ultra-miniature size connector, the stacking height of 3mm, 3.5mm, 4mm, and 5mm are provided.
2. Corresponding to Automatic Mounting
    The connector has the vacuum pick-up area to enable automatic mounting with the embossed tape packaging.
3. Metal Fitting Available
    The product including the metal fitting to prevent solder peeling is provided, considering the mounting on FPC.

■ Applications
    Mobile phone, LCD(Liquid Crystal Display), MO(Optical Disk), Note PC

Description : 0.5mm Pitch Board to Board Connector

■ Features
1. DF17 SERIES are the connector which has been developed mainly FOR the mobile phone.
2. PerFORmance Enhancement
    The receptacle is designed in a BOX structure and has also enhanced shock-proof, pinch-proof and scoop-proof perFORmance. In addition, the receptacle contact has employed the high scoop-proof bellows type.
3. With Metal Fitting available
    In order to grade up the strength against the mechanical stress, the metal fitting specification is also available.
4. Broad Variations in Contact Number
    The connectors are lined up per 10 contacts between 20 and 80 contacts to take countermeasures FOR multi-signalization.
5. Stacking Height 4 to 8mm
    The stacking height can be selected (per milimeter) between 4mm and 8mm in combination of the receptacle with the header.

■ Applications
    Mobile phones, LCD, miniature equipment and so on

Description : 0.5mm and 1mm Pitch Connectors FOR FPC/FFC

■ Features
1. Ease of USE and Space Savings
   Only one finger or 6.9N (Newtons) of FORce is required to lock Hirose’s rotational actuator (flip-lock) as compared to using 2 fingers and 39.2N to close a FFC/FPC connector from our competition.
   The Flip-Lock design also allows customers to place 2 or more connectors side by side as there is no need to waste additional board space FOR a side latch.
2. Strengthened Flip-lock Actuator
   The standard Flip-Lock requires only 2.0mm height above the board. A strengthened lock lever is available which only requires an additional 0.4mm.
3. Supports Thin FPC (0.18mm)
   Hirose does not require double-sided FPC to have any additional strengthening plate or stiffener and can thereFORe support a thickness of as little as 0.18mm +/-0.05.
4. Hirose Ensures Reliability
   Hirose’s patented half tuning FORk contacts maintain the required normal FORce without relying on the connector housing. With our competitor’s conventional products the housing walls support the contact FORce, which does not provide FOR long-term reliability.
5. Prevention of Solder Bridge
   Excess solder cavity absorbs excessive solder and avoids solder bridging.
6. Three different assembly types
   FH12 is offered in Top & Bottom Contact and Vertical Mount and offered in both a 0.5mm contact pitch as well as a 1.0mm contact pitch (bottom contact only).

Description : WS SERIES Hot-Molded Carbon Composition Potentiometer


■ Carbon composition/Industrial/Sealed
■ Locking-Bushing/Standard-Bushing
■ Meet MIL-R-94

Description : WS SERIES Hot-Molded Carbon Composition Potentiometer

■ Carbon composition/Industrial/Sealed
■ Locking-Bushing/Standard-Bushing
■ Meet MIL-R-94

Description : SMD Quartz Crystal

4 Pad Version · 12.9 x 4.73 mm

■ reflow soldering temperature: 260 °C max.

■ package height 5.0 mm


Description : Oven Controlled Crystal Oscillators (OCXO’s)

Small SMD OCXO with tight stability.
AT and SC-cut versions available.

• 5 MHz, 10 MHz, 13 MHz standard. Other frequencies available from 2 to 80 MHz
• Stability as low as ±5 x 10-8 over 0°C to 50°C
• Aging: 1 x 10-9 per day
• Package: 25.4 x 22 x 10.5 mm
• Supply voltage: +3.3 or +5.0 V

12345678910 Next

All Rights Reserved© datasheetq.com  [Privacy Policy ] [ Request Datasheet] [Contact Us]