DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

LTC1597BIN(RevA) View Datasheet(PDF) - Linear Technology

Part Name
Description
Manufacturer
LTC1597BIN Datasheet PDF : 20 Pages
First Prev 11 12 13 14 15 16 17 18 19 20
LTC1591/LTC1597
APPLICATIONS INFORMATION
5V
0.1μF
VREF
3
2
1
23 4
5
R1
RCOM REF VCC ROFS
RFB
16
DATA
INPUTS
R1
R2
LTC1597
ROFS RFB
16-BIT DAC
IOUT1 6
AGND 7
10 TO 21,
24 TO 27
WR LD CLR
WR
9 8 28
LD
CLR
22
DGND
33pF
LT1001
+
VOUT =
0V TO
–VREF
Unipolar Binary Code Table
DIGITAL INPUT
BINARY NUMBER
IN DAC REGISTER
MSB
1111
1000
0000
0000
1111
0000
0000
0000
1111
0000
0000
0000
LSB
1111
0000
0001
0000
ANALOG OUTPUT
VOUT
–VREF (65,535/65,536)
–VREF (32,768/65,536) = –VREF/ 2
–VREF (1/65,536)
0V
1591/97 F01b
Figure 1b. Unipolar Operation (2-Quadrant Multiplication) VOUT = 0V to – VREF
Bipolar Mode
(4-Quadrant Multiplying, VOUT = – VREF to VREF)
The LTC1591/LTC1597 contain on chip all the 4-quadrant
resistors necessary for bipolar operation. 4-quadrant
multiplying operation can be achieved with a minimum of
external components, a capacitor and a dual op amp, as
shown in Figure 2. With a fixed 10V reference, the circuit
shown gives a precision bipolar – 10V to 10V output
swing.
Op Amp Selection
Because of the extremely high accuracy of the 14-/16-bit
LTC1591/LTC1597, thought should be given to op amp
selection in order to achieve the exceptional performance
of which the part is capable. Fortunately, the sensitivity of
INL and DNL to op amp offset has been greatly reduced
compared to previous generations of multiplying DACs.
Op amp offset will contribute mostly to output offset and
gain and will have minimal effect on INL and DNL. For the
LTC1597, a 500μV op amp offset will cause about 0.55LSB
INL degradation and 0.15LSB DNL degradation with a 10V
full-scale range. The main effects of op amp offset will be
a degradation of zero-scale error equal to the op amp
offset, and a degradation of full-scale error equal to twice
the op amp offset. For the LTC1597, the same 500μV op
amp offset (2mV offset for LTC1591) will cause a 3.3LSB
zero-scale error and a 6.5LSB full-scale error with a 10V
full-scale range.
Op amp input bias current (IBIAS) contributes only a zero-
scale error equal to IBIAS(RFB/ROFS) = IBIAS(6k). For a
thorough discussion of 16-bit DAC settling time and op
amp selection, refer to Application Note 74, “Component
and Measurement Advances Ensure 16-Bit DAC Settling
Time.”
Reference Input and Grounding
For optimum performance the reference input of the
LTC1597 should be driven by a source impedance of less
than 1kΩ. However, these DACs have been designed to
minimize source impedance effects. An 8kΩ source im-
pedance degrades both INL and DNL by 0.2LSB.
As with any high resolution converter, clean grounding is
important. A low impedance analog ground plane and star
grounding should be used. AGND must be tied to the star
ground with as low a resistance as possible.
15917fa
14

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]