AD8364ACPZ-WP(RevB) View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
AD8364ACPZ-WP Datasheet PDF : 44 Pages
| |||
AD8364
Data Sheet
5
2.5
2.0
4
B
1.5
1.0
A
3
0.5
0
2
–0.5
–1.0
1
–1.5
–2.0
0
–60 –50 –40 –30 –20 –10
0
INPUT AMPLITUDE (dBm)
–2.5
10
20
Figure 9. OUT[A, B] Voltage and Log Conformance vs. Input Amplitude at
880 MHz, Typical Device, ADJ[A, B] = 0.5 V, Sine Wave, Differential Drive,
Balun = Mini-Circuits JTX-4-10T
5
2.5
2.0
4
1.5
B
1.0
A
3
0.5
0
2
–0.5
–1.0
1
–1.5
–2.0
0
–60 –50 –40 –30 –20 –10
0
INPUT AMPLITUDE (dBm)
–2.5
10
20
Figure 10. Distribution of OUT[A, B] Voltage and Error over Temperature After
Ambient Normalization vs. Input Amplitude for at Least 15 Devices from
Multiple Lots, Frequency = 880 MHz, ADJ[A, B] = 0.5 V, Sine Wave, Differential
Drive, Balun =JTX-4-10T
5
2.5
2.0
4
OUTN
1.5
OUTP
1.0
3
0.5
0
2
–0.5
–1.0
1
–1.5
–2.0
0
–60 –50 –40 –30 –20 –10
0
INPUT AMPLITUDE (dBm)
–2.5
10
20
Figure 12. OUT[P, N] Voltage and Log Conformance vs. Input Amplitude at
880 MHz, with B Input Held at −25 dBm and A Input Swept, Typical Device,
ADJ[A, B] = 0.5 V, Sine Wave, Differential Drive, Balun = JTX-4-10T
(Note that the OUTP and OUTN Error Curves Overlap)
5
2.5
4
2.0
3
1.5
2
1.0
1
0.5
0
0
–1
–0.5
–2
–1.0
–3
–4
–5
–60 –50 –40 –30 –20 –10
0
INPUT AMPLITUDE (dBm)
–1.5
–2.0
–2.5
10 20
Figure 13. Distribution of [OUTP − OUTN] Voltage and Error over
Temperature After Ambient Normalization vs. Input Amplitude for at Least
15 Devices from Multiple Lots, Frequency = 880 MHz, ADJ[A, B] =0.5 V, Sine
Wave, Differential Drive, PIN Ch. B = −25 dBm, Channel A Swept
0.20
0.15
0.10
0.05
0
–0.05
–0.10
–0.15
–0.20
–60 –50 –40 –30 –20 –10
0
INPUT AMPLITUDE (dBm)
10
20
Figure 11. Distribution of [OUTA – OUTB] Voltage vs. Input Amplitude over
Temperature for at Least 15 Devices from Multiple Lots, Frequency =
880 MHz, ADJ[A, B] = 0.5 V, Sine Wave, Differential Drive, Balun =JTX-4-10T
4
+20DEG
2
+30DEG
0
–2
-15DEG
–4
REF
+1dB
–6
+10DEG
–8
–10
+2dB
–12
–14
SERIES NAME INDICATES THE POLARITY
–16 AND MAGNITUDE OF THE DEVIATION
APPLIED TO THE INHA INPUT, RELATIVE
–18 TO THE INLA INPUT, AS REFERENCED TO
THE REF SIGNAL.
–20
–40 –35 –30 –25 –20 –15 –10 –5
RF INPUT AT INLA (dBm)
-2dB
-1dB
-10DEG
0 5 10
Figure 14. Log Conformance vs. Input Amplitude at Various Amplitude and
Phase Balance points, 880 MHz, Typical Device, ADJ[A, B] = 0.5 V, Sine Wave,
Differential Drive
Rev. B | Page 10 of 44
Share Link: 