ADE7752BARWZ-RL(2007) View Datasheet(PDF) - Analog Devices

Part Name

Description

Manufacturer

ADE7752BARWZ-RL
(Rev.:2007)

3-Phase, 3-Wire, and 4-Wire Energy Metering IC with Pulse Output

Analog Devices 

ADE7752B

THEORY OF OPERATION

The six signals from the current and voltage transducers are

digitized with ADCs. These ADCs are 16-bit, second-order

∑-Δ with an oversampling rate of 833 kHz. This analog input

structure greatly simplifies transducer interface by providing a

wide dynamic range and bipolar input for direct connection to

the transducer. High-pass filters in the current channels remove

the dc component from the current signals. This eliminates any

inaccuracies in the active power calculation due to offsets in the

voltage or current signals (see the HPF and Offset Effects section).

The active power calculation is derived from the instantaneous

power signal. The instantaneous power signal is generated by a

direct multiplication of the current and voltage signals of each

phase. To extract the active power component, the dc compo-

nent, the instantaneous power signal is low-pass filtered on

each phase. Figure 11 illustrates the instantaneous active power

signal and shows how the active power information can be

extracted by low-pass filtering the instantaneous power signal.

This method is used to extract the active power information

on each phase of the polyphase system. The total active power

information is then obtained by adding the individual phase

active power. This scheme correctly calculates active power

for nonsinusoidal current and voltage waveforms at all power

factors. All signal processing is carried out in the digital domain

for superior stability over temperature and time.

The low frequency output of the ADE7752B is generated by

accumulating the total active power information. This low

frequency inherently means a long accumulation time between

output pulses. The output frequency is therefore proportional to

the average active power. This average active power information

can, in turn, be accumulated (for example, by a counter) to

generate active energy information. Because of its high output

frequency and, therefore, shorter integration time, the CF

output is proportional to the instantaneous active power. This

pulse is useful for system calibration purposes that take place

under steady load conditions.

POWER FACTOR CONSIDERATIONS

Low-pass filtering, the method used to extract the active power

information from the individual instantaneous power signal, is

still valid when the voltage and current signals of each phase are

not in phase. Figure 12 displays the unity power factor condi-

tion and a displacement power factor (DPF) = 0.5, that is,

current signal lagging the voltage by 60°, for one phase of the

polyphase. Assuming that the voltage and current waveforms

are sinusoidal, the active power component of the instantaneous

power signal (the dc term) is given by

⎜⎝⎛

V×

2

1

⎟⎠⎞

×

cos(60°)

(2)

This is the correct active power calculation.

V×I

V×I

2

TIME

IAP

IAN

VAP

IBP

IBN

VBP

ICP

ICN

VCP

VN

p(t) = i(t) × v(t)

WHERE:

v(t) = V × cos (ωt)

i(t) = I × cos (ωt)

p(t) = V × I {1+ cos (2ωt)}

2

INSTANTANEOUS

POWER SIGNAL - p(t)

V×I

2

INSTANTANEOUS

ACTIVE POWER SIGNAL

VA

×

IA + VB ×

VC × IC

IB

+

2

ADC

HPF

MULTIPLIER

ADC

ADC

HPF

MULTIPLIER

ADC

ADC

HPF

MULTIPLIER

ADC

ABS

LPF

|X|

LPF

|X|

LPF

|X|

INSTANTANEOUS

TOTAL POWER

SIGNAL

DIGITAL-TO-FREQUENCY

F1

F2

DIGITAL-TO-FREQUENCY

CF

Figure 11. Signal Processing Block Diagram

Rev. 0 | Page 11 of 24

Share Link: