ADP7104CPZ-REDYKIT(RevB) View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
ADP7104CPZ-REDYKIT Datasheet PDF : 28 Pages
| |||
ADP7104
THEORY OF OPERATION
The ADP7104 is a low quiescent current, low-dropout linear
regulator that operates from 3.3 V to 20 V and provides up to
500 mA of output current. Drawing a low 1 mA of quiescent
current (typical) at full load makes the ADP7104 ideal for
battery-operated portable equipment. Typical shutdown
current consumption is 40 μA at room temperature.
Optimized for use with small 1 µF ceramic capacitors, the
ADP7104 provides excellent transient performance.
VIN
GND
EN/
UVLO
VREG
SHORT-CIRCUIT,
THERMAL
PROTECT
10µA
SHUTDOWN
PGOOD
R1
R2
VOUT
PG
SENSE
1.22V
REFERENCE
Figure 59. Fixed Output Voltage Internal Block Diagram
VIN
GND
EN/
UVLO
VREG
10µA
SHORT-CIRCUIT,
THERMAL
PROTECT
SHUTDOWN
PGOOD
R2
VOUT
PG
ADJ
1.22V
REFERENCE
Figure 60. Adjustable Output Voltage Internal Block Diagram
Internally, the ADP7104 consists of a reference, an error
amplifier, a feedback voltage divider, and a PMOS pass
transistor. Output current is delivered via the PMOS pass
device, which is controlled by the error amplifier. The error
amplifier compares the reference voltage with the feedback
voltage from the output and amplifies the difference. If the
feedback voltage is lower than the reference voltage, the gate
of the PMOS device is pulled lower, allowing more current to
pass and increasing the output voltage. If the feedback voltage
Data Sheet
is higher than the reference voltage, the gate of the PMOS
device is pulled higher, allowing less current to pass and
decreasing the output voltage.
The ADP7104 is available in seven fixed output voltage options,
ranging from 1.5 V to 9 V and in an adjustable version with an
output voltage that can be set to between 1.22 V and 19 V by an
external voltage divider. The output voltage can be set according
to the following equation:
VOUT = 1.22 V(1 + R1/R2)
VIN = 8V
CIN +
1µF
OFF
ON
R3
100kΩ
R4
100kΩ
VIN VOUT
R1
40.2kΩ
ADJ
EN/
UVLO
GND PG
R2
13kΩ
+ COUT VOUT = 5V
1µF
RPG
100kΩ
PG
Figure 61. Typical Adjustable Output Voltage Application Schematic
The value of R2 should be less than 200 kΩ to minimize errors
in the output voltage caused by the ADJ pin input current. For
example, when R1 and R2 each equal 200 kΩ, the output voltage
is 2.44 V. The output voltage error introduced by the ADJ pin input
current is 2 mV or 0.08%, assuming a typical ADJ pin input
current of 10 nA at 25°C.
The ADP7104 uses the EN/UVLO pin to enable and disable
the VOUT pin under normal operating conditions. When
EN/UVLO is high, VOUT turns on, when EN is low, VOUT
turns off. For automatic startup, EN/UVLO can be tied to VIN.
The ADP7104 incorporates reverse current protections
circuitry that prevents current flow backwards through the pass
element when the output voltage is greater than the input
voltage. A comparator senses the difference between the input
and output voltages. When the difference between the input
voltage and output voltage exceeds 55 mV, the body of the PFET
is switched to VOUT and turned off or opened. In other words,
the gate is connected to VOUT.
Rev. B | Page 16 of 28
Share Link: 