MB90P663APFM View Datasheet(PDF) - Fujitsu

Part Name

Description

Manufacturer

MB90P663APFM

16-bit Proprietary Microcontroller

Fujitsu 

MB90660A Series

4. PROM Option Bitmap

The programming method is the same as a PROM, and can be set by programming values to addresses indicated

in the memory map.

The following bit map shows the relation between bits and options.

• PROM Option Bitmap

Bit

Address

00004H

7

P07

Pull-up

1: No

0: Yes

00008H

P17

Pull-up

1: No

0: Yes

0000CH

P27

Pull-up

1: No

0: Yes

00010H

P43

Pull-up

1: No

0: Yes

00014H *1 P47

Pull-up

1: No

0: Yes

00018H

Open

6

P06

Pull-up

1: No

0: Yes

P16

Pull-up

1: No

0: Yes

P26

Pull-up

1: No

0: Yes

P42

Pull-up

1: No

0: Yes

P46

Pull-up

1: No

0: Yes

P66

Pull-up

1: No

0: Yes

5

P05

Pull-up

1: No

0: Yes

P15

Pull-up

1: No

0: Yes

P25

Pull-up

1: No

0: Yes

P41

Pull-up

1: No

0: Yes

P45

Pull-up

1: No

0: Yes

P65

Pull-up

1: No

0: Yes

4

P04

Pull-up

1: No

0: Yes

P14

Pull-up

1: No

0: Yes

P24

Pull-up

1: No

0: Yes

P40

Pull-up

1: No

0: Yes

P44

Pull-up

1: No

0: Yes

P64

Pull-up

1: No

0: Yes

3

P03

Pull-up

1: No

0: Yes

P13

Pull-up

1: No

0: Yes

P23

Pull-up

1: No

0: Yes

P33

Pull-up

1: No

0: Yes

RST

Pull-up

1: No

0: Yes

P63

Pull-up

1: No

0: Yes

2

P02

Pull-up

1: No

0: Yes

P12

Pull-up

1: No

0: Yes

P22

Pull-up

1: No

0: Yes

P32

Pull-up

1: No

0: Yes

DTTI

Pull-up

1: No

0: Yes

P62

Pull-up

1: No

0: Yes

1

0

P01

Pull-up

1: No

0: Yes

P00

Pull-up

1: No

0: Yes

P11

Pull-up

1: No

0: Yes

P10

Pull-up

1: No

0: Yes

P21

Pull-up

1: No

0: Yes

P20

Pull-up

1: No

0: Yes

P31

Pull-up

1: No

0: Yes

P30

Pull-up

1: No

0: Yes

Accept asyn-

chronous

reset

1: Yes

0: No

MD1/MD0*2

Pull-up

1: No

0: Yes

P61

Pull-up

1: No

0: Yes

P60

Pull-up

1: No

0: Yes

Initially (value when blank), all bits are “1”.

*1: Under this release, the pull-up resistor is cut-off during stop mode for pins for which the pull-up option was

selected. (Pins for which the circuit type shown in the “s Pin Description” is B or E.)

However, the pull-up resistor is not cut-off even in stop mode for P44 to 47, RST, DTTI (pins for which the circuit

type shown in the “s Pin Description” is D or G), and MD1 and MD0.

*2: Whether or not a pull-up/pull-down resistor is present for MD2, MD1 and MD0 is determined as follows. If pull-

up/pull-down resistor is selected, it is included with all 2 (or 3) pins. Presence or absence of the pull-up or pull-

down resistors for the mode terminal cannot be selected for each pin.

Pin

MB90P663A

MB90663A/2A

MD2

No

Pull-down can be selected

MD1

With pull-up resistor

With pull-up resistor

MD0

With pull-up resistor

With pull-up resistor

Notes: • “FFH” must be set to addresses no defined in the table above.

• Since the option setting for the MB90P663A takes 8 machine cycles, the option setting is not made until

a clock is provided after power-on. (This results in no pull-up for all pins, and asynchronous reset input is

accepted.)

17

Share Link: