PIC16LC622T-04 View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC16LC622T-04

EPROM-Based 8-Bit CMOS Microcontrollers

Microchip Technology 

PIC16C62X

6.0 TIMER0 MODULE

The Timer0 module timer/counter has the following

features:

• 8-bit timer/counter

• Readable and writable

• 8-bit software programmable prescaler

• Internal or external clock select

• Interrupt on overflow from FFh to 00h

• Edge select for external clock

Figure 6-1 is a simplified block diagram of the Timer0

module.

Timer mode is selected by clearing the T0CS bit

(OPTION<5>). In Timer mode, the TMR0 will increment

every instruction cycle (without prescaler). If Timer0 is

written, the increment is inhibited for the following two

cycles (Figure 6-2 and Figure 6-3). The user can work

around this by writing an adjusted value to TMR0.

Counter mode is selected by setting the T0CS bit. In

this mode, Timer0 will increment either on every rising

or falling edge of pin RA4/T0CKI. The incrementing

edge is determined by the source edge (T0SE) control

bit (OPTION<4>). Clearing the T0SE bit selects the

rising edge. Restrictions on the external clock input are

discussed in detail in Section 6.2.

The prescaler is shared between the Timer0 module

and the Watchdog Timer. The prescaler assignment is

controlled in software by the control bit PSA

(OPTION<3>). Clearing the PSA bit will assign the

prescaler to Timer0. The prescaler is not readable or

writable. When the prescaler is assigned to the Timer0

module, prescale value of 1:2, 1:4, ..., 1:256 are

selectable. Section 6.3 details the operation of the

prescaler.

6.1 TIMER0 Interrupt

Timer0 interrupt is generated when the TMR0 register

timer/counter overflows from FFh to 00h. This overflow

sets the T0IF bit. The interrupt can be masked by

clearing the T0IE bit (INTCON<5>). The T0IF bit

(INTCON<2>) must be cleared in software by the

Timer0 module interrupt service routine before re-

enabling this interrupt. The Timer0 interrupt cannot

wake the processor from SLEEP, since the timer is shut

off during SLEEP. See Figure 6-4 for Timer0 interrupt

timing.

FIGURE 6-1:

TIMER0 BLOCK DIAGRAM

RA4/T0CKI

pin

FOSC/4

T0SE

Data Bus

0

PSout

8

1

Sync with

1

Internal

TMR0

Programmable 0

Prescaler

clocks

PSout

(2 Tcy delay)

T0CS

PS<2:0>

PSA

Note 1: Bits T0SE, T0CS, PS2, PS1, PS0 and PSA are located in the OPTION register.

2: The prescaler is shared with Watchdog Timer (Figure 6-6).

Set Flag bit T0IF

on Overflow

FIGURE 6-2:

TIMER0 (TMR0) TIMING: INTERNAL CLOCK/NO PRESCALER

PC

(Program

Counter)

Instruction

Fetch

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

PC-1

PC

PC+1

PC+2

PC+3

PC+4

PC+5

PC+6

MOVWF TMR0 MOVF TMR0,WMOVF TMR0,WMOVF TMR0,WMOVF TMR0,WMOVF TMR0,W

TMR0

T0

Instruction

Executed

T0+1

T0+2

NT0

NT0+1

NT0+2

T0

Write TMR0 Read TMR0 Read TMR0 Read TMR0 Read TMR0 Read TMR0

executed

reads NT0 reads NT0 reads NT0 reads NT0 + 1 reads NT0 + 2

 2003 Microchip Technology Inc.

DS30235J-page 31

Share Link: