ST6285BQ1 View Datasheet(PDF) - STMicroelectronics

Part Name

Description

Manufacturer

ST6285BQ1

8-BIT OTP/EPROM MCU WITH LCD DRIVER, EEPROM AND A/D CONVERTER

STMicroelectronics 

ST62T85B/E85B

5 SOFTWARE

5.1 ST6 ARCHITECTURE

The ST6 software has been designed to fully use bits of the opcode with the byte following the op-

the hardware in the most efficient way possible code. The instructions (JP, CALL) which use the

while keeping byte usage to a minimum; in short, extended addressing mode are able to branch to

to provide byte efficient programming capability. any address of the 4K bytes Program space.

The ST6 core has the ability to set or clear any

register or RAM location bit of the Data space with

a single instruction. Furthermore, the program

An extended addressing mode instruction is two-

byte long.

may branch to a selected address depending on

the status of any bit of the Data space. The carry

bit is stored with the value of the bit when the SET

or RES instruction is processed.

Program Counter Relative. The relative address-

ing mode is only used in conditional branch in-

structions. The instruction is used to perform a test

and, if the condition is true, a branch with a span of

-15 to +16 locations around the address of the rel-

5.2 ADDRESSING MODES

ative instruction. If the condition is not true, the in-

The ST6 core offers nine addressing modes,

) which are described in the following paragraphs.

t(s Three different address spaces are available: Pro-

gram space, Data space, and Stack space. Pro-

c gram space contains the instructions which are to

u be executed, plus the data for immediate mode in-

d structions. Data space contains the Accumulator,

ro the X,Y,V and W registers, peripheral and In-

put/Output registers, the RAM locations and Data

P ROM locations (for storage of tables and con-

te stants). Stack space contains six 12-bit RAM cells

le used to stack the return addresses for subroutines

and interrupts.

so Immediate. In the immediate addressing mode,

b the operand of the instruction follows the opcode

O location. As the operand is a ROM byte, the imme-

- diate addressing mode is used to access con-

) stants which do not change during program execu-

t(s tion (e.g., a constant used to initialize a loop coun-

ter).

uc Direct. In the direct addressing mode, the address

d of the byte which is processed by the instruction is

ro stored in the location which follows the opcode. Di-

rect addressing allows the user to directly address

P the 256 bytes in Data Space memory with a single

te two-byte instruction.

le Short Direct. The core can address the four RAM

o registers X,Y,V,W (locations 80h, 81h, 82h, 83h) in

s the short-direct addressing mode. In this case, the

binstruction is only one byte and the selection of the

Olocation to be processed is contained in the op-

struction which follows the relative instruction is

executed. The relative addressing mode instruc-

tion is one-byte long. The opcode is obtained in

adding the three most significant bits which char-

acterize the kind of the test, one bit which deter-

mines whether the branch is a forward (when it is

0) or backward (when it is 1) branch and the four

less significant bits which give the span of the

branch (0h to Fh) which must be added or sub-

tracted to the address of the relative instruction to

obtain the address of the branch.

Bit Direct. In the bit direct addressing mode, the

bit to be set or cleared is part of the opcode, and

the byte following the opcode points to the ad-

dress of the byte in which the specified bit must be

set or cleared. Thus, any bit in the 256 locations of

Data space memory can be set or cleared.

Bit Test & Branch. The bit test and branch ad-

dressing mode is a combination of direct address-

ing and relative addressing. The bit test and

branch instruction is three-byte long. The bit iden-

tification and the tested condition are included in

the opcode byte. The address of the byte to be

tested follows immediately the opcode in the Pro-

gram space. The third byte is the jump displace-

ment, which is in the range of -127 to +128. This

displacement can be determined using a label,

which is converted by the assembler.

Indirect. In the indirect addressing mode, the byte

processed by the register-indirect instruction is at

the address pointed by the content of one of the in-

direct registers, X or Y (80h,81h). The indirect reg-

code. Short direct addressing is a subset of the di- ister is selected by the bit 4 of the opcode. A regis-

rect addressing mode. (Note that 80h and 81h are ter indirect instruction is one byte long.

also indirect registers).

Inherent. In the inherent addressing mode, all the

Extended. In the extended addressing mode, the information necessary to execute the instruction is

12-bit address needed to define the instruction is contained in the opcode. These instructions are

obtained by concatenating the four less significant one byte long.

60/78

60

Share Link: