P1201MB60AP View Datasheet(PDF) - Teccor Electronics

Part Name

Description

Manufacturer

P1201MB60AP

100 mA, battrax quad negative SLIC protector

Teccor Electronics 

Balanced Three-chip SIDACtor Device

Balanced Three-chip SIDACtor Device

1

6 This balanced protector is a surface mount alternative to the modified TO-220 package.

Based on a six-pin surface mount SOIC package, it uses Teccor’s patented “Y”

2

5 (US Patent 4,905,119) configuration. It is available in surge current ratings up to 500 A.

3

4

SIDACtor devices are used to enable equipment to meet various regulatory requirements

including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968 (formerly

known as FCC Part 68).

Electrical Parameters

Part

Number *

P1553U_

P1803U_

P2103U_

P2353U_

P2703U_

P3203U_

P3403U_

P5103U_

A2106U_3 **

A5030U_3 **

VDRM

Volts

VS

Volts

Pins 1-3, 1-4

130

180

150

210

170

250

200

270

230

300

270

350

300

400

420

600

170

250

400

550

VDRM

Volts

VS

Volts

Pins 3-4

130

180

150

210

170

250

200

270

230

300

270

350

300

400

420

600

50

80

270

350

VT

IDRM

IS

IT

IH

CO

Volts µAmps mAmps Amps mAmps pF

8

5

800

2.2

150

40

8

5

800

2.2

150

40

8

5

800

2.2

150

40

8

5

800

2.2

150

40

8

5

800

2.2

150

30

8

5

800

2.2

150

30

8

5

800

2.2

150

30

8

5

800

2.2

150

30

8

5

800

2.2

120

40

8

5

800

2.2

150

30

* For individual “UA”, “UB”, and “UC” surge ratings, see table below.

** Asymmetrical

General Notes:

• All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range.

• IPP is a repetitive surge rating and is guaranteed for the life of the product.

• Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities.

• VDRM is measured at IDRM.

• VS is measured at 100 V/µs.

• Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request.

• Off-state capacitance is measured between Pins 1-3 and 1-4 at 1 MHz with a 2 V bias and is a typical value for “UA” product. “UB”

and “UC” capacitance is approximately 2x higher.

• Device is designed to meet balance requirements of GTS 8700 and GR 974.

Surge Ratings

Series

A

B

C

IPP

2x10 µs

Amps

150

250

500

IPP

8x20 µs

Amps

150

250

400

IPP

10x160 µs

Amps

90

150

200

IPP

10x560 µs

Amps

50

100

150

IPP

10x1000 µs

Amps

45

80

100

ITSM

60 Hz

Amps

20

30

50

di/dt

Amps/µs

500

500

500

http://www.teccor.com

+1 972-580-7777

2 - 20

© 2002 Teccor Electronics

SIDACtor® Data Book and Design Guide

Share Link: