P1200CD62TP View Datasheet(PDF) - Teccor Electronics
Part Name
Description
Manufacturer
P1200CD62TP Datasheet PDF : 212 Pages
| |||
Four-Port Longitudinal Two-chip Protector
Four-Port Longitudinal Two-chip Protector
This hybrid Single In-line Package (SIP) protects four twisted pairs from overcurrent and
overvoltage conditions. Comprised of eight discrete DO-214AA SIDACtor devices and eight
TeleLink surface mount fuses, it is ideal for densely populated line cards that cannot afford
PCB inefficiencies or the use of series power resistors. Surge current ratings up to 500 A
are available.
F2
Tip 2
5
Z2
Gnd 3
Z1
Ring 4
1
F1
F4
Tip 7
10
Z4
Gnd 8
Z3
Ring 9
6
F3
F6
Tip 12
15
Z6
Gnd 13
Z5
Ring 14
11
F5
F8
Tip 17
20
Z8
Gnd 18
Z7
Ring 19
16
F7
Electrical Parameters
Part
Number *
P0602Z_
P1402Z_
P1602Z_
P2202Z_
P2702Z_
P3002Z_
P3602Z_
P4202Z_
P4802Z_
P6002Z_
VDRM
Volts
VS
Volts
Pins 2-3, 4-3, 7-8, 9-8,
12-13, 14-13, 17-18, 19-18
25
40
58
77
65
95
90
130
120
160
140
180
160
220
190
250
220
300
275
350
VDRM
Volts
VS
Volts
Pins 2-4, 7-9,
12-14, 17-19
50
80
116
154
130
190
180
260
240
320
280
360
320
440
380
500
440
600
550
700
VT
Volts
4
4
4
4
4
4
4
4
4
4
IDRM
µAmps
5
5
5
5
5
5
5
5
5
5
IS
mAmps
800
800
800
800
800
800
800
800
800
800
IT
Amps
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
IH
mAmps
50
150
150
150
150
150
150
150
150
150
CO
pF
Pins
2-3, 3-4
110
50
50
40
40
40
40
30
30
30
* For individual “ZA,” “ZB,” and “ZC” surge ratings, see table below.
General Notes:
• All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range.
• IPP is a repetitive surge rating and is guaranteed for the life of the product.
• Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities.
• VDRM is measured at IDRM.
• VS is measured at 100 V/µs.
• Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request.
• Off-state capacitance is measured between Pins 4-3 and Pins 2-3 at 1 MHz with a 2 V bias and is a typical value for “ZA” product.
“ZB” and “ZC” capacitance is approximately 2x higher.
• Device is designed to meet balance requirements of GTS 8700 and GR 974.
• Lower capacitance MC versions may be available. Contact factory for further information.
Surge Ratings
Series
A
B
C
IPP
2x10 µs
Amps
150
250
500
IPP
8x20 µs
Amps
150
250
400
IPP
10x160 µs
Amps
90
150
200
IPP
10x560 µs
Amps
50
100
150
IPP
10x1000 µs
Amps
45
80
100
ITSM
60 Hz
Amps
20
30
50
di/dt
Amps/µs
500
500
500
http://www.teccor.com
+1 972-580-7777
2 - 42
© 2002 Teccor Electronics
SIDACtor® Data Book and Design Guide
Share Link: 