PIC12LCE518T-04ISM View Datasheet(PDF) - Microchip Technology
Part Name
Description
Manufacturer
PIC12LCE518T-04ISM Datasheet PDF : 113 Pages
| |||
PIC12C5XX
13.3 DC CHARACTERISTICS:
PIC12C508A/509A (Commercial, Industrial, Extended)
PIC12C518/519 (Commercial, Industrial, Extended)
PIC12CR509A (Commercial, Industrial, Extended)
DC CHARACTERISTICS
Param
No.
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating temperature 0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating voltage VDD range as described in DC spec Section 13.1 and
Section 13.2.
Sym Min Typ† Max Units
Conditions
D030
Input Low Voltage
I/O ports
with TTL buffer
D031
D032
D033
D033
D040
with Schmitt Trigger buffer
MCLR, GP2/T0CKI (in EXTRC mode)
OSC1 (in EXTRC mode)
OSC1 (in XT and LP)
Input High Voltage
I/O ports
with TTL buffer
D040A
D041
with Schmitt Trigger buffer
D042 MCLR, GP2/T0CKI
D042A OSC1 (XT and LP)
D043 OSC1 (in EXTRC mode)
D070 GPIO weak pull-up current (Note 4)
MCLR pull-up current
Input Leakage Current (Notes 2, 3)
D060 I/O ports
VIL
VSS
- 0.8V
VSS
- 0.15VDD
VSS
- 0.2VDD
VSS
- 0.2VDD
VSS
- 0.2VDD
VSS
- 0.3VDD
VIH
-
0.25VDD + -
VDD
0.8V
2.0V
-
VDD
0.8VDD -
VDD
0.8VDD -
VDD
0.7VDD -
VDD
0.9VDD -
VDD
IPUR
30
250 400
-
-
-
30
IIL
-
-
+1
D061 T0CKI
D063 OSC1
-
-
+5
-
-
+5
Output Low Voltage
D080 I/O ports
VOL
-
-
0.6
D080A
-
-
0.6
Output High Voltage
D090 I/O ports (Note 3)
VOH VDD - 0.7 -
-
D090A
VDD - 0.7 -
-
Capacitive Loading Specs on
Output Pins
D100 OSC2 pin
COSC2 -
-
15
D101 All I/O pins
CIO
-
-
50
V For 4.5V ≤ VDD ≤ 5.5V
V otherwise
V
V
Note 1
V Note 1
V 4.5V ≤ VDD ≤ 5.5V
V otherwise
V For entire VDD range
V
V Note 1
V
µA VDD = 5V, VPIN = VSS
µA VDD = 5V, VPIN = VSS
µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT and LP osc
configuration
V IOL = 8.5 mA, VDD = 4.5V,
–40°C to +85°C
V IOL = 7.0 mA, VDD = 4.5V,
–40°C to +125°C
V IOH = -3.0 mA, VDD = 4.5V,
–40°C to +85°C
V IOH = -2.5 mA, VDD = 4.5V,
–40°C to +125°C
pF In XT and LP modes when exter-
nal clock is used to drive OSC1.
pF
†
Note 1:
2:
3:
4:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
In EXTRC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC12C5XX be driven with external clock in RC mode.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
Negative current is defined as coming out of the pin.
This spec. applies when GP3/MCLR is configured as MCLR. The leakage current of the MCLR circuit is higher than the
standard I/O logic.
DS40139E-page 82
© 1999 Microchip Technology Inc.
Share Link: 