PIC12CR509AT-04 View Datasheet(PDF) - Microchip Technology
Part Name
Description
Manufacturer
PIC12CR509AT-04 Datasheet PDF : 113 Pages
| |||
PIC12C5XX
13.4 DC CHARACTERISTICS:
PIC12LC508A/509A (Commercial, Industrial)
PIC12LC518/519 (Commercial, Industrial)
PIC12LCR509A (Commercial, Industrial)
DC CHARACTERISTICS
Param
No.
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating voltage VDD range as described in DC spec Section 13.1 and
Section 13.2.
Sym Min Typ† Max Units
Conditions
D030
D031
D032
D033
D033
D040
D040A
D041
D042
D042A
D043
D070
D060
D061
D063
D080
D080A
D090
D090A
D100
D101
†
Note 1:
2:
3:
4:
Input Low Voltage
I/O ports
VIL
with TTL buffer
VSS
- 0.8V V For 4.5V ≤ VDD ≤ 5.5V
VSS
- 0.15VDD V otherwise
with Schmitt Trigger buffer
VSS
- 0.2VDD V
MCLR, GP2/T0CKI (in EXTRC mode)
VSS
- 0.2VDD V
OSC1 (in EXTRC mode)
VSS
- 0.2VDD V Note 1
OSC1 (in XT and LP)
VSS
- 0.3VDD V Note 1
Input High Voltage
I/O ports
VIH
-
with TTL buffer
0.25VDD + - VDD
0.8V
V 4.5V ≤ VDD ≤ 5.5V
2.0V
-
VDD
V otherwise
with Schmitt Trigger buffer
0.8VDD -
VDD
V For entire VDD range
MCLR, GP2/T0CKI
0.8VDD -
VDD
V
OSC1 (XT and LP)
0.7VDD -
VDD
V Note 1
OSC1 (in EXTRC mode)
0.9VDD -
VDD
V
GPIO weak pull-up current (Note 4) IPUR
30
250 400 µA VDD = 5V, VPIN = VSS
MCLR pull-up current
-
-
-
30
µA VDD = 5V, VPIN = VSS
Input Leakage Current (Notes 2, 3)
I/O ports
IIL
-
-
+1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-imped-
ance
T0CKI
-
-
+5
µA Vss ≤ VPIN ≤ VDD
OSC1
-
-
+5
µA Vss ≤ VPIN ≤ VDD, XT and LP osc
configuration
Output Low Voltage
I/O ports
VOL
-
-
0.6
V IOL = 8.5 mA, VDD = 4.5V,
–40°C to +85°C
-
-
0.6
V IOL = 7.0 mA, VDD = 4.5V,
–40°C to +125°C
Output High Voltage
I/O ports (Note 3)
VOH VDD - 0.7 -
-
V IOH = -3.0 mA, VDD = 4.5V,
–40°C to +85°C
VDD - 0.7 -
-
V IOH = -2.5 mA, VDD = 4.5V,
–40°C to +125°C
Capacitive Loading Specs on
Output Pins
OSC2 pin
COSC
-
-
15
pF In XT and LP modes when exter-
2
nal clock is used to drive OSC1.
All I/O pins
CIO
-
-
50
pF
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
In EXTRC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC12C5XX be driven with external clock in RC mode.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
Negative current is defined as coming out of the pin.
This spec. applies when GP3/MCLR is configured as MCLR. The leakage current of the MCLR circuit is higher than the
standard I/O logic.
© 1999 Microchip Technology Inc.
DS40139E-page 83
Share Link: 