PIC12F615-EMD View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC12F615-EMD

8-Pin Flash-Based, 8-Bit CMOS Microcontrollers

Microchip Technology 

PIC12F609/615/617/12HV609/615

TABLE 2-3: PIC12F609/HV609 SPECIAL FUNCTION REGISTERS SUMMARY BANK 1

Addr

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Value on

POR, BOR

Page

Bank 1

80h INDF

Addressing this location uses contents of FSR to address data memory (not a physical register)

xxxx xxxx 25, 116

81h OPTION_RE

G

GPPU

INTEDG

T0CS

T0SE

PSA

PS2

PS1

PS0 1111 1111 19, 116

82h PCL

Program Counter’s (PC) Least Significant Byte

0000 0000 25, 116

83h STATUS

IRP(1)

RP1(1)

RP0

TO

PD

Z

DC

C

0001 1xxx 18, 116

84h FSR

85h TRISIO

Indirect Data Memory Address Pointer

—

—

TRISIO5 TRISIO4 TRISIO3(4) TRISIO2

TRISIO1

xxxx xxxx 25, 116

TRISIO0 --11 1111 44, 116

86h

—

Unimplemented

—

—

87h

—

Unimplemented

—

—

88h

—

Unimplemented

—

—

89h

—

Unimplemented

—

—

8Ah PCLATH

8Bh INTCON

—

—

—

Write Buffer for upper 5 bits of Program Counter

---0 0000 25, 116

GIE

PEIE

T0IE

INTE

GPIE

T0IF

INTF

GPIF(3) 0000 0000 20, 116

8Ch PIE1

—

—

—

—

CMIE

—

—

TMR1IE ---- 0--0 21, 116

8Dh

—

Unimplemented

—

—

8Eh PCON

—

—

—

—

—

—

POR

BOR ---- --qq 23, 116

8Fh

—

Unimplemented

—

—

90h OSCTUNE

—

—

—

TUN4

TUN3

TUN2

TUN1

TUN0 ---0 0000 41, 116

91h

—

Unimplemented

—

—

92h

—

Unimplemented

—

—

93h

—

Unimplemented

—

—

94h

—

95h WPU(2)

Unimplemented

—

—

WPU5

WPU4

—

WPU2

WPU1

WPU0

—

—

--11 -111 46, 116

96h IOC

—

—

IOC5

IOC4

IOC3

IOC2

IOC1

IOC0 --00 0000 46, 116

97h

—

Unimplemented

—

—

98h

—

Unimplemented

—

—

99h

—

Unimplemented

—

—

9Ah

—

Unimplemented

—

—

9Bh

—

Unimplemented

—

—

9Ch

—

Unimplemented

—

—

9Dh

—

Unimplemented

—

—

9Eh

—

Unimplemented

—

—

9Fh ANSEL

—

—

—

—

ANS3

—

ANS1

ANS0 ---- 1-11 45, 117

Legend:

Note 1:

2:

3:

4:

– = Unimplemented locations read as ‘0’, u = unchanged, x = unknown, q = value depends on condition, shaded = unimplemented

IRP and RP1 bits are reserved, always maintain these bits clear.

GP3 pull-up is enabled when MCLRE is ‘1’ in the Configuration Word register.

MCLR and WDT Reset does not affect the previous value data latch. The GPIF bit will clear upon Reset but will set again if the mismatch

exists.

TRISIO3 always reads as ‘1’ since it is an input only pin.

DS41302D-page 16

 2010 Microchip Technology Inc.

Share Link: