PIC16C65B-04E/SO View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC16C65B-04E/SO

8-Bit CMOS Microcontrollers with A/D Converter

Microchip Technology 

PIC16C63A/65B/73B/74B

TABLE C-2: SPECIFICATION DIFFERENCES

Param

No.

Symbol

Characteristic

PIC16C63/65A/73A/74A

Min Typ† Max

PIC16C63A/65B/73B/74B

Unit

Min

Typ† Max

Core

D001 VDD

D001A

Supply Voltage

4.0

—

6.0

4.0

—

5.5

V

—

—

—

VBOR(1)

—

5.5

V

D005 BVDD

Brown-out Reset Voltage

3.7

4.0

4.3

3.65

—

4.35

V

D150* VOD

Open-Drain High Voltage on

RA4

—

—

14.0

-

—

8.5

V

A/D Converter

A20

VREF

Reference voltage

3.0

— VDD + 0.3

2.5

— VDD + 0.3 V

131

TCNV

Conversion time (Note 2)

(not including S/H time)

—

9.5

—

(Note 3)

11

(Note 4)

—

11

TAD

(Note 4)

SSP in SPI mode

71

TscH

71A

SCK input high Continuous TCY+20 —

time (Slave mode) Single Byte

— 1.25TCY + 30 —

—

ns

40

—

—

ns

72

TscL

72A

SCK input low

time

(Slave mode)

Continuous TCY+20 —

Single Byte

— 1.25TCY + 30 —

—

ns

40

—

—

ns

73

TdiV2scH Setup time of SDI data input to 50

—

—

TdiV2scL SCK edge

100

—

—

ns

73A

TB2B

Last clock edge of Byte1 to the —

—

(Note 5)

1st clock edge of Byte2

—

1.5TCY + 40 —

—

ns

74

TscH2diL Hold time of SDI data input to

50

—

—

TscL2diL SCK edge

100

—

—

ns

75

TdoR

SDO data output PIC16CXX

—

10

25

rise time

PIC16LCXX

—

10

25

ns

—

20

45

ns

78

TscR

SCK output rise PIC16CXX

—

10

25

time (Master

mode)

PIC16LCXX

—

10

25

ns

—

20

45

ns

80

TscH2doV SDO data output PIC16CXX

—

—

50

TscL2doV valid after SCK

edge

PIC16LCXX

—

—

50

ns

—

—

100

ns

83

TscH2ssH SS ↑ after SCK edge

TscL2ssH

—

—

50

1.5TCY + 40 —

—

ns

† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not

tested.

Note 1: When BOR is enabled, the device will operate until VDD drops below VBOR.

2: ADRES register may be read on the following TCY cycle.

3: This is the time that the actual conversion requires.

4: This is the time from when the GO/DONE bit is set, to when the conversion result appears in ADRES.

5: Specification 73A is only required if specifications 71A and 72A are used.

 2000 Microchip Technology Inc.

DS30605C-page 167

Share Link: