PIC16LCR67-04/P View Datasheet(PDF) - Microchip Technology
Part Name
Description
Manufacturer
PIC16LCR67-04/P Datasheet PDF : 336 Pages
| |||
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
23.3 DC Characteristics: PIC16C66/67-04 (Commercial, Industrial, Extended)
PIC16C66/67-10 (Commercial, Industrial, Extended)
PIC16C66/67-20 (Commercial, Industrial, Extended)
PIC16LC66/67-04 (Commercial, Industrial)
DC CHARACTERISTICS
Param
No.
Characteristic
D030
D030A
D031
D032
D033
D040
D040A
Input Low Voltage
I/O ports
with TTL buffer
with Schmitt Trigger buffer
MCLR, OSC1 (in RC mode)
OSC1 (in XT, HS and LP)
Input High Voltage
I/O ports
with TTL buffer
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +125˚C for extended,
-40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec Section 23.1 and
Section 23.2
Sym Min Typ Max Units
Conditions
†
VIL
VSS - 0.15VDD V For entire VDD range
VSS - 0.8V
V 4.5V ≤ VDD ≤ 5.5V
VSS - 0.2VDD V
Vss - 0.2VDD V
Vss - 0.3VDD V Note1
VIH
-
2.0 - VDD
0.25VDD - VDD
+ 0.8V
V 4.5V ≤ VDD ≤ 5.5V
V For entire VDD range
D041
with Schmitt Trigger buffer
0.8VDD - VDD
V For entire VDD range
D042 MCLR
0.8VDD - VDD
V
D042A OSC1 (XT, HS and LP)
0.7VDD - VDD
V Note1
D043 OSC1 (in RC mode)
D070 PORTB weak pull-up current
0.9VDD - VDD
IPURB
50 250 400
V
µA VDD = 5V, VPIN = VSS
Input Leakage Current (Notes 2, 3)
D060 I/O ports
IIL
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
D061 MCLR, RA4/T0CKI
D063 OSC1
-
-
±5
µA Vss ≤ VPIN ≤ VDD
-
-
±5
µA Vss ≤ VPIN ≤ VDD, XT, HS and
LP osc configuration
Output Low Voltage
D080 I/O ports
VOL
-
- 0.6
V IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
D080A
D083 OSC2/CLKOUT (RC osc config)
-
- 0.6
V IOL = 7.0 mA, VDD = 4.5V,
-40°C to +125°C
-
- 0.6
V IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
D083A
-
- 0.6
V IOL = 1.2 mA, VDD = 4.5V,
-40°C to +125°C
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
DS30234D-page 266
© 1997 Microchip Technology Inc.
Share Link: 