PIC16F689T-I/SO View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC16F689T-I/SO

20-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology

Microchip Technology 

PIC16F631/677/685/687/689/690

17.2 DC Characteristics: PIC16F631/677/685/687/689/690-I (Industrial)

PIC16F631/677/685/687/689/690-E (Extended) (Continued)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No.

Device Characteristics

Min. Typ† Max. Units

VDD

Conditions

Note

D020

Power-down Base

Current(IPD)(2)

—

0.05 1.2

μA

—

0.15 1.5

μA

2.0 WDT, BOR, Comparators, VREF and

3.0 T1OSC disabled

—

0.35 1.8

μA

5.0

D021

—

90

500

nA

—

1.0

2.2

μA

3.0 -40°C ≤ TA ≤ +25°C

2.0 WDT Current(1)

—

2.0

4.0

μA

3.0

D022

—

3.0

7.0

μA

—

42

60

μA

5.0

3.0 BOR Current(1)

D023

—

85

122

μA

—

32

45

μA

—

60

78

μA

5.0

2.0 Comparator Current(1), both

3.0 comparators enabled

D024

—

120 160

μA

—

30

36

μA

5.0

2.0 CVREF Current(1) (high range)

—

45

55

μA

3.0

D024a*

—

75

95

μA

—

39

47

μA

5.0

2.0 CVREF Current(1) (low range)

—

59

72

μA

3.0

—

98

124

μA

5.0

D025

—

2.0

5.0

μA

2.0 T1OSC Current, 32.768 kHz

—

2.5

5.5

μA

3.0

D026

—

3.0

7.0

μA

—

0.30 1.6

μA

—

0.36 1.9

μA

5.0

3.0 A/D Current(1), no conversion in

5.0 progress

D027

—

90

125

μA

3.0 VP6 Current

—

125 162

μA

5.0

† Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are

not tested.

Note 1: The test conditions for all IDD measurements in Active Operation mode are: OSC1 = external square wave, from

rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.

2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading

and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current

consumption.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended

by the formula IR = VDD/2REXT (mA) with REXT in kΩ.

4: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is

enabled. The peripheral Δ current can be determined by subtracting the base IDD or IPD current from this limit. Max

values should be used when calculating total current consumption.

5: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.

© 2008 Microchip Technology Inc.

DS41262E-page 235

Share Link: