PIC16F720-EML View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC16F720-EML

20-Pin Flash Microcontrollers

Microchip Technology 

PIC16(L)F720/721

23.3 DC Characteristics: PIC16(L)F720/721-I/E (Power-Down)

PIC16LF720/721

PIC16F720/721

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C  TA  +85°C for industrial

-40°C  TA  +125°C for extended

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C  TA  +85°C for industrial

-40°C  TA  +125°C for extended

Param.

No.

Device Characteristics

Min.

D020

D020

D021

D021

Power-down Base Current (IPD)(2)

—

—

—

—

—

—

—

—

—

Typ†

0.04

0.05

18

20

23

0.5

0.8

20

22

Max.

+85°C

Max.

+125°C

Units

1

8

A

2

9

A

47

55

A

58

72

A

60

84

A

4

9

A

5

11

A

49

57

A

60

74

A

Conditions

VDD

Note

1.8 Base IPD

3.0

1.8 Base IPD

3.0

5.0

1.8 IPD LPWDT on (Note 1)

3.0

1.8 IPD LPWDT on (Note 1)

3.0

D021A

—

25

63

—

14

29

—

15

31

86

A

5.0

35

A

1.8 IPD FVR on (Note 1)

38

A

3.0

D021A

D022

—

39

77

90

A

1.8 IPD FVR on (Note 1)

—

46

98

108

A

3.0

—

91

160

170

A

5.0

—

—

—

—

A

1.8 IPD BOR on (Note 1)

—

7

15

26

A

3.0

D022

—

—

—

—

26

64

—

29

67

—

A

1.8 IPD BOR on (Note 1)

78

A

3.0

91

A

5.0

D027

D027

D027A

—

1.5

4

—

2

5

10

A

1.8 IPD ADC on (Note 1, Note 3)

11

A

3.0 non-convert

—

19

48

—

21

59

57

A

1.8 IPD ADC on (Note 1, Note 3)

74

A

3.0 non-convert

—

24

62

87

A

5.0

— 250 400

410

A

1.8 IPD ADC on (Note 1, Note 3)

— 260 420

430

A

3.0 convert

D027A

†

Note 1:

2:

3:

— 280 430

440

A

1.8 IPD ADC on (Note 1, Note 3)

— 300 450

460

A

3.0 convert

— 320 470

480

A

5.0

Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are

not tested.

The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is

enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max

values should be used when calculating total current consumption.

The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.

A/D oscillator source is FRC.

 2010-2013 Microchip Technology Inc.

DS41430D-page 189

Share Link: