PIC16C715-10E/SP View Datasheet(PDF) - Microchip Technology
Part Name
Description
Manufacturer
PIC16C715-10E/SP Datasheet PDF : 176 Pages
| |||
PIC16C71X
Applicable Devices 710 71 711 715
15.3 DC Characteristics: PIC16C71-04 (Commercial, Industrial)
PIC16C71-20 (Commercial, Industrial)
PIC16LC71-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
OOperating temperature 0˚C ≤ TA ≤ +70˚C (commercial)
DC CHARACTERISTICS
-40˚C ≤ TA ≤ +85˚C (industrial)
Operating voltage VDD range as described in DC spec Section 15.1
and Section 15.2.
Param
Characteristic
Sym Min Typ Max Units
Conditions
No.
†
Input Low Voltage
I/O ports
VIL
D030
with TTL buffer
VSS - 0.15V V For entire VDD range
D031
with Schmitt Trigger buffer
VSS - 0.8V V 4.5 ≤ VDD ≤ 5.5V
D032 MCLR, OSC1 (in RC mode)
VSS - 0.2VDD V
D033 OSC1 (in XT, HS and LP)
VSS - 0.3VDD V Note1
Input High Voltage
I/O ports (Note 4)
VIH
-
D040
with TTL buffer
2.0 - VDD V 4.5 ≤ VDD ≤ 5.5V
D040A
0.25VDD - VDD
For entire VDD range
+ 0.8V
D041
with Schmitt Trigger buffer
0.85VDD - VDD
For entire VDD range
D042 MCLR, RB0/INT
0.85VDD - VDD V
D042A OSC1 (XT, HS and LP)
0.7VDD - VDD V Note1
D043 OSC1 (in RC mode)
0.9VDD - VDD V
D070 PORTB weak pull-up current
IPURB 50 250 †400 µA VDD = 5V, VPIN = VSS
Input Leakage Current (Notes 2, 3)
D060 I/O ports
IIL
-
- ±1 µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
D061 MCLR, RA4/T0CKI
-
- ±5 µA Vss ≤ VPIN ≤ VDD
D063 OSC1
-
- ±5 µA Vss ≤ VPIN ≤ VDD, XT, HS and
LP osc configuration
Output Low Voltage
D080 I/O ports
VOL
-
- 0.6 V IOL = 8.5mA, VDD = 4.5V,
-40°C to +85°C
D083 OSC2/CLKOUT (RC osc config)
-
- 0.6 V IOL = 1.6mA, VDD = 4.5V,
-40°C to +85°C
Output High Voltage
D090 I/O ports (Note 3)
VOH VDD - 0.7 -
-
V IOH = -3.0mA, VDD = 4.5V,
-40°C to +85°C
D092 OSC2/CLKOUT (RC osc config)
VDD - 0.7 -
-
V IOH = -1.3mA, VDD = 4.5V,
-40°C to +85°C
D130* Open-Drain High Voltage
VOD
-
- 14 V RA4 pin
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1 pin is a Schmitt trigger input. It is not recommended that the
PIC16C71 be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
4: PIC16C71 Rev. "Ax" INT pin has a TTL input buffer. PIC16C71 Rev. "Bx" INT pin has a Schmitt Trigger input
buffer.
DS30272A-page 138
© 1997 Microchip Technology Inc.
Share Link: 