PIC16F1512T-E/SO View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC16F1512T-E/SO

28-Pin Flash Microcontrollers with XLP Technology

Microchip Technology 

PIC16(L)F1512/3

TABLE 25-3: POWER-DOWN CURRENTS (IPD)(1,2,4)

PIC16LF1512/3

Standard Operating Conditions (unless otherwise stated)

PIC16F1512/3

Param

No.

Device Characteristics

Min.

Typ†

Max.

+85°C

Max.

+125°C

Units

VDD

Conditions

Note

D022

D022

D023

D023

D023A

— 0.02 1.0

8.0

A

1.8 WDT, BOR, FVR, and SOSC

— 0.03 2.0

9.0

A

3.0 disabled, all Peripherals Inactive

— 0.20 3.0

11

A

2.3 WDT, BOR, FVR, and SOSC

— 0.30 4.0

12

A

3.0 disabled, all Peripherals Inactive

— 0.40

6

15

A

5.0

— 0.30

6

14

A

1.8 LPWDT Current

— 0.60

7

17

A

3.0

— 0.50

6

15

A

2.3 LPWDT Current

— 0.77

7

20

A

3.0

— 0.85

8

22

A

5.0

—

10

28

30

A

1.8 FVR current

—

12

30

33

A

3.0

D023A

—

18

33

—

19

36

35

A

2.3 FVR current

37

A

3.0

D024

—

20

37

—

8.0

17

45

A

5.0

20

A

3.0 BOR Current

D024

D024A

—

8

17

—

9

20

— 0.80

4

30

A

3.0 BOR Current

40

A

5.0

8

A

3.0 LPBOR Current

D024A

D025

D025

— 0.30

4

14

A

3.0 LPBOR Current

— 0.45

8

17

A

5.0

—

0.6

5

9

A

1.8 SOSC Current

—

2.5

8.5

12

A

3.0

—

1

6

10

A

2.3 SOSC Current

D026

D026

*

†

Note 1:

2:

3:

4:

—

2.2

8.5

20

A

3.0

—

5.5

15

25

A

5.0

—

0.1

1.5

9

A

1.8 A/D Current (Note 3),

—

0.2

2.7

10

A

3.0 no conversion in progress

—

0.3

4

— 0.35

5

11

A

2.3 A/D Current (Note 3),

13

A

3.0 no conversion in progress

— 0.45

8

16

A

5.0

These parameters are characterized but not tested.

Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are

not tested.

The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is

enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max

values should be used when calculating total current consumption.

The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.

A/D oscillator source is FRC.

Specification for PIC16F1512/3 devices assumes that Low-Power Sleep mode is selected, when available, via the

VREGCON register (see Section 8.2.2 “Peripheral Usage in Sleep” and Register 8-1).

DS40001624C-page 290

 2012-2014 Microchip Technology Inc.

Share Link: