STM32F050G4U7 View Datasheet(PDF) - STMicroelectronics

Part Name

Description

Manufacturer

STM32F050G4U7

Low- and medium-density advanced ARM™-based 32-bit MCU with up to 32 Kbytes Flash, timers, ADC and comm. interfaces

STMicroelectronics 

Electrical characteristics

STM32F050xx

Input/output AC characteristics

The definition and values of input/output AC characteristics are given in Figure 22 and

Table 47, respectively.

Unless otherwise specified, the parameters given are derived from tests performed under

ambient temperature and VDD supply voltage conditions summarized in Table 15: General

operating conditions.

Table 47. I/O AC characteristics(1)

OSPEEDRy

[1:0] value(1)

Symbol

Parameter

Conditions

Min Max Unit

fmax(IO)out Maximum frequency(2) CL = 50 pF, VDD = 2 V to 3.6 V

x0

tf(IO)out

Output high to low level

fall time

tr(IO)out

Output low to high level

rise time

CL = 50 pF, VDD = 2 V to 3.6 V

fmax(IO)out Maximum frequency(2) CL = 50 pF, VDD = 2 V to 3.6 V

01

tf(IO)out

Output high to low level

fall time

tr(IO)out

Output low to high level

rise time

CL = 50 pF, VDD = 2 V to 3.6 V

-

2 MHz

- 125(3)

ns

- 125(3)

- 10 MHz

- 25(3)

ns

- 25(3)

11

FM+

configuration

(4)

fmax(IO)out Maximum frequency(2)

tf(IO)out

Output high to low level

fall time

tr(IO)out

Output low to high level

rise time

fmax(IO)out Maximum frequency(2)

tf(IO)out

Output high to low level

fall time

tr(IO)out

Output low to high level

rise time

CL = 30 pF, VDD = 2.7 V to 3.6 V

CL = 50 pF, VDD = 2.7 V to 3.6 V

CL = 50 pF, VDD = 2 V to 2.7 V

CL = 30 pF, VDD = 2.7 V to 3.6 V

CL = 50 pF, VDD = 2.7 V to 3.6 V

CL = 50 pF, VDD = 2 V to 2.7 V

CL = 30 pF, VDD = 2.7 V to 3.6 V

CL = 50 pF, VDD = 2.7 V to 3.6 V

CL = 50 pF, VDD = 2 V to 2.7 V

CL = 50 pF, VDD = 2 V to 3.6 V

CL = 50 pF, VDD = 2 V to 3.6 V

CL = 50 pF, VDD = 2 V to 3.6 V

- 50

- 30 MHz

- 20

-

5(3)

-

8(3)

- 12(3)

ns

-

5(3)

-

8(3)

- 12(3)

-

2(3) MHz

- 12(3)

ns

- 34(3)

tEXTIpw

Pulse width of external

signals detected by the

EXTI controller

10 -

ns

1. The I/O speed is configured using the OSPEEDRx[1:0] bits. Refer to the RM0091 reference manual for a description of

GPIO Port configuration register.

2. The maximum frequency is defined in Figure 22.

3. Guaranteed by design, not tested in production.

4. When FM+ configuration is set, the I/O speed control is bypassed. Refer to the STM32F05xxx reference manual RM0091

for a detailed description of FM+ I/O configuration.

70/97

Doc ID 023683 Rev 1

Share Link: