STV2246 View Datasheet(PDF) - STMicroelectronics

Part Name

Description

Manufacturer

STV2246

I²C bus-controlled multistandard single chip TV processor

STMicroelectronics 

STV224X, STV228X, STV223X - FUNCTIONAL DESCRIPTION

3 FUNCTIONAL DESCRIPTION

The STV224XH/228XH is an integrated device – Built-in sound bandpass.

that processes PIF, SIF, Video and Chroma sig-

nals while scanning for PAL, SECAM and NTSC

standards. It includes a base band chroma delay

line, Video, SVHS and audio switches.

– PLL FM Demodulator for 4.5, 5.5, 6.0 or 6.5 MHz

carriers. The Sound Standard is selected by the

MCU. The FM demodulator VCO is automatically

calibrated using the chroma crystal VCO refer-

ence frequency. The FM Demodulator VCO is

3.1 DETAILED FEATURES

automatically calibrated for all sound standards

3.1.1 Power Supplies

independently of the chroma crystal VCO fre-

quency, which is either 4.4 MHz or 3.5 MHz. For

VCCIF: 5 V power supply dedicated to IF proces-

sors. GNDIF is the ground reference of these

each sound carrier frequency, the IC sends an

indication of the sound subcarrier level to the

parts.

MCU so that it can select the proper standard.

VCCD: 5 V power supply dedicated to I²C bus and

digital parts. GNDD is the ground reference of

) these parts.

t(s VCC1: 8 V power supply for video switches, scan-

ning part and the chroma decoder. GND 1 is the

c ground reference of all these functions.

u VCC2: 8 V power supply for the luminance, RGB

d processing parts audio switch and internal CVBS

ro output. GND2 is the ground reference of these

parts.

P 3.1.2 Picture Intermediate Frequency (PIF)

te – AGC amplifier.

– PLL synchronous demodulator. Bus-controlled

le VCO for integrated tuning of the external LC res-

o onator. For a 38.9 MHz VCO, the LC coil specifi-

s cation has to be:

b C = 39pF, f = 44 MHz ±2% (LC not connected).

For a 33.9 MHz VCO (L’), the VCO can be

O switched via the bus control.

- – Digital AFC via bus.

) – IF Automatic Gain Control (AGC)

t(s Negative modulation: top sync regulation, regu-

lation of overmodulated signals (overmodulation

c regulation circuit enabled through bus control).

u Positive modulation: main regulation on white

d level with black level limitation.

ro – Tuner-delayed AGC with bus control for AGC

gain and threshold. Tuner AGC output status can

P be read in I²C bus read register.

te – CVBS output with two bus-controlled ampli-

tudes. CVBS output at 2 VPP if external sound

letrap is not connected (QSS mode, for example).

o CVBS output at 2.3 VPP if external sound trap is

connected.

bs 3.1.3 Sound Intermediate Frequency (SIF) and

In Normal mode, the maximum FM deviation is

200 kHz. In Audio FM Wide mode (BGDKI), the

maximum FM deviation is 400 kHz. The Audio

FM Wide mode of the STV224XH must be used

in QSS applications only, using standard specific

SAW filters (DK SAW filter or BG SAW filter).

– The sound subcarrier level is valid when the FM

Demodulation VCO is calibrated. This informa-

tion can be read via the I²C Bus.

– Bus controls for FM de-emphasis (50 or 75 µs)

and FM deviation ±25 or ±50 kHz).

– AM demodulator.

– Sound demodulator output: either an AM or FM

signal can be the output for the Mono chassis

– Sound subcarriers for the Stereo chassis.

3.1.4 Audio Switch

– One SCART switch.

– Bus-controlled volume and mute. Zero-crossing

function on volume control.

– Automatic Volume Levelling (AVL) function can

be enabled via the I²C bus.

– AVL status (Min. or Max. AVL Gain) can be read

in I²C bus register.

– The AM sound can be selected on the main au-

dio output for the Stereo chassis.

3.1.5 Surface Acoustic Wave (SAW) Filter

Switch Control

– SAW filter switch control pin is available in the

TQFP64 package. The SAW filter switch control

pin is used to select the correct SAW filter char-

acteristics (e.g.: M/N or BGDK characteristics).

In a multi-standard chassis, two output voltages

are selected via the I²C bus (low level voltage at

0.4 V Max., and high level voltage at 4 V Min.).

Sound Demodulators

3.1.6 Video Switches

– QSS structure.

– SIF Automatic Gain Control (QSS mode).

– Video switch with three CVBS inputs and one

CVBS output (CVBSOUT1) which may be used

to drive a teletext decoder.

20/86

Share Link: