ST7PLIT115BF1M3 View Datasheet(PDF) - STMicroelectronics

Part Name

Description

Manufacturer

ST7PLIT115BF1M3

8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI

STMicroelectronics 

ST7LITE1xB

7 SUPPLY, RESET AND CLOCK MANAGEMENT

The device includes a range of utility features for

securing the application in critical situations (for

example in case of a power brown-out), and re-

ducing the number of external components.

Main features

■ Clock Management

– 1 MHz internal RC oscillator (enabled by op-

tion byte, available on ST7LITE15B and

ST7LITE19B devices only)

– 1 to 16 MHz External crystal/ceramic resona-

tor (selected by option byte)

– External Clock Input (enabled by option byte)

– PLL for multiplying the frequency by 8 or 4

(enabled by option byte)

– For clock ART counter only: PLL32 for multi-

plying the 8 MHz frequency by 4 (enabled by

option byte). The 8 MHz input frequency is

mandatory and can be obtained in the follow-

ing ways:

–1 MHz RC + PLLx8

–16 MHz external clock (internally divided

by 2)

–2 MHz. external clock (internally divided by

2) + PLLx8

–Crystal oscillator with 16 MHz output fre-

quency (internally divided by 2)

■ Reset Sequence Manager (RSM)

■ System Integrity Management (SI)

– Main supply Low voltage detection (LVD) with

reset generation (enabled by option byte)

– Auxiliary Voltage detector (AVD) with interrupt

capability for monitoring the main supply (en-

abled by option byte)

7.1 INTERNAL RC OSCILLATOR ADJUSTMENT

The device contains an internal RC oscillator with

an accuracy of 1% for a given device, temperature

and voltage range (4.5V-5.5V). It must be calibrat-

ed to obtain the frequency required in the applica-

tion. This is done by software writing a 10-bit cali-

bration value in the RCCR (RC Control Register)

and in the bits 6:5 in the SICSR (SI Control Status

Register).

Whenever the microcontroller is reset, the RCCR

returns to its default value (FFh), i.e. each time the

device is reset, the calibration value must be load-

ed in the RCCR. Predefined calibration values are

stored in EEPROM for 3 and 5V VDD supply volt-

ages at 25°C, as shown in the following table.

RCCR Conditions

RCCRH0 VDD=5V

RCCRL0

TA=25°C

fRC=1MHz

RCCRH1 VDD=3.3V

RCCRL1

TA=25°C

fRC=1MHz

ST7LITE1xB

Address

DEE0h 1) (CR[9:2])

DEE1h 1) (CR[1:0])

DEE2h 1) (CR[9:2])

DEE3h 1) (CR[1:0])

1. DEE0h, DEE1h, DEE2h and DEE3h addresses

are located in a reserved area of non-volatile

memory. They are read-only bytes for the applica-

tion code. This area cannot be erased or pro-

grammed by any ICC operation.

For compatibility reasons with the SICSR register,

CR[1:0] bits are stored in the 5th and 6th position

of DEE1 and DEE3 addresses.

Notes:

– In 38-pulse ICC mode, the internal RC oscillator

is forced as a clock source, regardless of the se-

lection in the option byte. For ST7LITE10B devic-

es which do not support the internal RC

oscillator, the “option byte disabled” mode must

be used (35-pulse ICC mode entry, clock provid-

ed by the tool).

– See “ELECTRICAL CHARACTERISTICS” on

page 110. for more information on the frequency

and accuracy of the RC oscillator.

– To improve clock stability and frequency accura-

cy, it is recommended to place a decoupling ca-

pacitor, typically 100nF, between the VDD and

VSS pins as close as possible to the ST7 device.

– These bytes are systematically programmed by

ST, including on FASTROM devices.

Caution: If the voltage or temperature conditions

change in the application, the frequency may need

to be recalibrated.

Refer to application note AN1324 for information

on how to calibrate the RC frequency using an ex-

ternal reference signal.

7.2 PHASE LOCKED LOOP

The PLL can be used to multiply a 1MHz frequen-

cy from the RC oscillator or the external clock by 4

or 8 to obtain fOSC of 4 or 8 MHz. The PLL is ena-

bled and the multiplication factor of 4 or 8 is select-

ed by 2 option bits.

– The x4 PLL is intended for operation with VDD in

the 2.7V to 3.3V range

23/159

1

Share Link: