PIC18LF4420T-I/SO データシートの表示（PDF） - Microchip Technology

部品番号

コンポーネント説明

メーカー

PIC18LF4420T-I/SO

28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology

Microchip Technology 

PIC18F2420/2520/4420/4520

26.2 DC Characteristics: Power-Down and Supply Current

PIC18F2420/2520/4420/4520 (Industrial)

PIC18LF2420/2520/4420/4520 (Industrial) (Continued)

PIC18LFX42X/X52X

(Industrial)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C ≤ TA ≤ +85°C for industrial

PIC18FX42X/X52X

(Industrial)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C ≤ TA ≤ +85°C for industrial

ParamNo.

Device

Typ Max Units

Conditions

Supply Current (IDD)(2,3)

PIC18LFX42X/X52X 15 31.5 µA

-40°C

15 30 µA

15 28.5 µA

+25°C

+85°C

VDD = 2.0V

PIC18LFX42X/X52X 40 63 µA

35 60 µA

30 57 µA

-40°C

+25°C

+85°C

VDD = 3.0V

FOSC = 31 kHz

(RC_RUN mode,

INTRC source)

All devices 105 168 µA

-40°C

90 160 µA

80 152 µA

+25°C

+85°C

VDD = 5.0V

PIC18LFX42X/X52X 0.32 630 µA

-40°C

0.33 600 µA

+25°C

VDD = 2.0V

0.33 570 µA

+85°C

PIC18LFX42X/X52X 0.6 1.3 mA

0.55 1.2 mA

0.6 1.1 mA

-40°C

+25°C

+85°C

VDD = 3.0V

FOSC = 1 MHz

(RC_RUN mode,

INTOSC source)

All devices 1.1 2.3 mA

-40°C

1.1 2.2 mA

+25°C

VDD = 5.0V

1.0 2.1 mA

+85°C

Legend:

Note 1:

2:

3:

4:

5:

Shading of rows is to assist in readability of the table.

The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured

with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that

add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin

loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have

an impact on the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

For RC oscillator configurations, current through REXT is not included. The current through the resistor can be

estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature

crystals are available at a much higher cost.

BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be

less than the sum of both specifications.

 2004 Microchip Technology Inc.

Preliminary

DS39631A-page 327

Share Link: