PIC16F753-I/SLQTP 데이터 시트보기 (PDF) - Microchip Technology

부품명

상세내역

제조사

PIC16F753-I/SLQTP

14/16-Pin, Flash-Based 8-Bit CMOS Microcontrollers

Microchip Technology 

PIC16F753/HV753

22.8 DC Characteristics: PIC16F753/HV753-I (Industrial)

PIC16F753/HV753-E (Extended)

DC CHARACTERISTICS

Param.

No.

Sym.

VIL

D030

D030A

D031

VIH

D040

D040A

D041

D042

IIL

D060

Characteristic

Input Low Voltage

I/O port:

with TTL buffer

with Schmitt Trigger buffer

Input High Voltage

I/O ports:

with TTL buffer

with Schmitt Trigger buffer

MCLR

Input Leakage Current(1,2)

I/O ports

D061

D063

D070*

IPUR

D080 VOL

RA3/MCLR(2,3)

PORTA Weak Pull-up

Current(4)

Output Low Voltage

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C  TA  +85°C for industrial

-40°C  TA  +125°C for extended

Min.

Typ† Max. Units

Conditions

Vss

—

0.8

V 4.5V  VDD  5.5V

Vss

— 0.15 VDD V 2.0V  VDD  4.5V

Vss

— 0.2 VDD V 2.0V  VDD  5.5V

—

2.0

—

VDD

V 4.5V  VDD 5.5V

0.25 VDD + 0.8 —

VDD

V 2.0V  VDD  4.5V

0.8 VDD

—

VDD

V 2.0V  VDD  5.5V

0.8 VDD

—

VDD

V

—

0.1

1

A VSS VPIN VDD,

Pin at high-impedance

—

0.7

5

A VSS VPIN VDD

—

0.1

5

A EC Configuration

50

250

400

A VDD = 5.0V, VPIN = VSS

I/O ports (excluding RA0, RA2)

—

—

RA0, RA2

—

—

D090 VOH

Output High Voltage

—

0.6

V IOL = 7.0 mA, VDD = 4.5V,

-40°C to +125°C

—

0.6

V IOL = 8.5 mA, VDD = 4.5V,

-40°C to +85°C

—

0.6

V IOL = 14 mA, VDD = 4.5V,

-40°C to +125°C

—

0.6

V IOL = 17 mA, VDD = 4.5V,

-40°C to +85°C

I/O ports(1) (excluding RA0, RA2)

VDD – 0.7

—

—

V IOH = -2.5 mA, VDD = 4.5V,

-40°C to +125°C

VDD – 0.7

—

—

V IOH = -3.0 mA, VDD = 4.5V,

-40°C to +85°C

RA0, RA2

VDD – 0.7

—

—

V IOH = -5.0 mA, VDD = 4.5V,

-40°C to +125°C

VDD – 0.7

—

—

V IOH = -6.0 mA, VDD = 4.5V,

-40°C to +85°C

* These parameters are characterized but not tested.

† Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are

not tested.

Note 1: Negative current is defined as current sourced by the pin.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent

normal operating conditions. Higher leakage current may be measured at different input voltages.

3: This specification applies to RA3/MCLR configured as RA3 with the internal weak pull-up disabled.

4: This specification applies to all weak pull-up pins, including the weak pull-up found on RA3/MCLR. When RA3/MCLR is

configured as MCLR Reset pin, the weak pull-up is always enabled.

D40001709A-page 196

Preliminary

 2013 Microchip Technology Inc.

Share Link: