PIC18LF4420T-I/SO 데이터 시트보기 (PDF) - Microchip Technology

부품명

상세내역

제조사

PIC18LF4420T-I/SO

28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology

Microchip Technology 

PIC18F2420/2520/4420/4520

26.2 DC Characteristics: Power-Down and Supply Current

PIC18F2420/2520/4420/4520 (Industrial)

PIC18LF2420/2520/4420/4520 (Industrial) (Continued)

PIC18LFX42X/X52X

(Industrial)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C ≤ TA ≤ +85°C for industrial

PIC18FX42X/X52X

(Industrial)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C ≤ TA ≤ +85°C for industrial

ParamNo.

Device

Typ Max Units

Conditions

Supply Current (IDD)(2,3)

PIC18LFX42X/X52X 165 315 µA

-40°C

175 300 µA

190 285 µA

+25°C

+85°C

VDD = 2.0V

PIC18LFX42X/X52X 250 470 µA

270 450 µA

290 430 µA

-40°C

+25°C

+85°C

VDD = 3.0V

FOSC = 1 MHz

(RC_IDLE mode,

INTOSC source)

All devices 500 840 µA

-40°C

520 800 µA

550 760 µA

+25°C

+85°C

VDD = 5.0V

PIC18LFX42X/X52X 340 525 µA

-40°C

350 500 µA

+25°C

VDD = 2.0V

360 475 µA

+85°C

PIC18LFX42X/X52X 520 735 µA

540 700 µA

580 665 µA

-40°C

+25°C

+85°C

VDD = 3.0V

FOSC = 4 MHz

(RC_IDLE mode,

INTOSC source)

All devices 1.0 1.6 mA

-40°C

1.1 1.5 mA

+25°C

VDD = 5.0V

1.1 1.4 mA

+85°C

Legend:

Note 1:

2:

3:

4:

5:

Shading of rows is to assist in readability of the table.

The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured

with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that

add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin

loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have

an impact on the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

For RC oscillator configurations, current through REXT is not included. The current through the resistor can be

estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature

crystals are available at a much higher cost.

BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be

less than the sum of both specifications.

 2004 Microchip Technology Inc.

Preliminary

DS39631A-page 329

Share Link: