CS493102-CL Просмотр технического описания (PDF) - Cirrus Logic

Номер в каталоге

Компоненты Описание

производитель

CS493102-CL

Multi-Standard Audio Decoder Family

Cirrus Logic 

CS49300 Family DSP

0x00000

0x07FFF

0x08000

0x0FFFF

Dolby Digital with

Pro Logic II with Cirrus

Extra Surround

MPEG Multichannel with

Pro Logic II

0x10000

DTS-ES Extended Surround

0x17FFF

0x18000

DTS-ES Neo:6

0x1FFFF

0x20000

0x27FFF

0x28000

0x2FFFF

0x30000

0x37FFF

0x38000

0x3FFFF

HDCD

LOGIC7

MP3

Virtual Dolby Digital with

VMAx VirtualTheater

Address line uC15, uC16, and

uC17 used for paging

Figure 41. Example Contents of a Paged 32 Kilo-

bytes External Memory (Total 256 Kilobytes)

The flow diagram given in Figure 36 demonstrates

the interaction required by the microcontroller

during autoboot. After placing the decoder into a

reset state, the host selects the page in memory

containing first code by driving uC15 to a low state.

The host also drives ABOOT low and holds it in a

low state until the rising edge of RESET to initiate

autoboot. As noted in the autoboot section, the

ABOOT pin should be connected to an open-drain

output of the microcontroller so as to allow the

specified pull-up resistor to generate the high

value. The open-drain driver is required because

the DSP will begin using the pin as an output after

a successful download (INTREQ and ABOOT are

multiplexed on the same pin).

After waiting for 175 ms, the download should have

completed. During the wait period, the host should

ignore all INTREQ behavior (mask the INTREQ

interrupt). The host can then verify that the code

has successfully initialized itself by reading a

variable from the application and checking the

returned value against the default value. Any

variable can be used for the verification step, but a

robust design will select a variable whose value is

neither all 0’s nor all 1’s. If the first read attempt

returns an incorrect value, a 5 ms wait should be

inserted and the read should be repeated. If a

second invalid number is read, the entire boot

process should be repeated. When the number

returned matches the default value for the variable

read, the host knows that the application is

resident in the DSP and awaiting further

instruction. Please see Section 8.2, “Autoboot” on

page 57 for more information.

For systems that would prefer to store all

application codes in an external parallel Flash

Memory (vs. a OTP EPROM) in order to realize a

“field-upgradable” system, please contact

dsp_support@crystal.cirrus.com for information

about how to control the GPIO pins of the DSP via

messaging to the SPI or I2C port.

8.8. CDB49300-MEMA.0

The CDB49300-MEMA.0 is an external memory

adapter card designed for use with the

CDB4923/CDB4930 REV-A.0 Evaluation Board.

The schematic for the CDB49300-MEMA.0 is

shown in Figure 42. This board is an example of

one possible external memory configuration.

In addition to autobooting from external EPROM,

certain application codes require real-time access

to external SRAM, such as decoding of AAC

Multichannel streams, which have a 5.1 channel

output. These applications require that the DSP

has real-time access to 70nS (or faster) 32

Kilobyte SRAM. The 128 Kilobyte SRAM on the

CDB49300-MEMA.0 is made accessible by the

DSP when the host drives uC18 high. The external

256 Kilobyte EPROM is accessible to the DSP

when the host controller drives uC18 low. The with

uC15, uC16, and uC17 lines are used to page

between the various code images.

66

DS339F7

Share Link: