PIC16LC926-I/PT 查看數據表（PDF） - Microchip Technology

零件编号

产品描述 (功能)

生产厂家

PIC16LC926-I/PT

64/68-Pin CMOS Microcontrollers with LCD Driver

Microchip Technology 

PIC16C925/926

9.0 SYNCHRONOUS SERIAL PORT

(SSP) MODULE

The Synchronous Serial Port (SSP) module is a serial

interface useful for communicating with other periph-

eral or microcontroller devices. These peripheral

devices may be serial EEPROMs, shift registers, dis-

play drivers, A/D converters, etc. The SSP module can

operate in one of two modes:

• Serial Peripheral Interface (SPITM)

• Inter-Integrated Circuit (I2CTM)

Refer to Application Note AN578, "Use of the SSP

Module in the I 2C Multi-Master Environment.”

REGISTER 9-1:

SSPSTAT: SERIAL PORT STATUS REGISTER (ADDRESS 94h)

R/W-0

R/W-0

R-0

R-0

R-0

R-0

R-0

SMP

CKE

D/A

P

S

R/W

UA

bit 7

R-0

BF

bit 0

bit 7

SMP: SPI Data Input Sample Phase bit

SPI Master mode:

1 = Input data sampled at end of data output time

0 = Input data sampled at middle of data output time

SPI Slave mode:

SMP must be cleared when SPI is used in Slave mode

bit 6

CKE: SPI Clock Edge Select bit (see Figure 9-3, Figure 9-4, and Figure 9-5)

CKP = 0:

1 = Data transmitted on rising edge of SCK

0 = Data transmitted on falling edge of SCK

CKP = 1:

1 = Data transmitted on falling edge of SCK

0 = Data transmitted on rising edge of SCK

bit 5

D/A: Data/Address bit (I2C mode only)

1 = Indicates that the last byte received or transmitted was data

0 = Indicates that the last byte received or transmitted was address

bit 4

P: STOP bit (I2C mode only. This bit is cleared when the SSP module is disabled, or when the START

bit was detected last.)

1 = Indicates that a STOP bit has been detected last (this bit is ’0’ on RESET)

0 = STOP bit was not detected last

bit 3

S: START bit (I2C mode only. This bit is cleared when the SSP module is disabled, or when the STOP

bit was detected last.)

1 = Indicates that a START bit has been detected last (this bit is ’0’ on RESET)

0 = START bit was not detected last

bit 2

R/W: Read/Write bit Information (I2C mode only)

This bit holds the R/W bit information following the last address match. This bit is only valid from the

address match to the next START bit, STOP bit, or ACK bit.

1 = Read

0 = Write

bit 1

UA: Update Address (10-bit I2C mode only)

1 = Indicates that the user needs to update the address in the SSPADD register

0 = Address does not need to be updated

bit 0

BF: Buffer Full Status bit

Receive (SPI and I2C modes):

1 = Receive complete, SSPBUF is full

0 = Receive not complete, SSPBUF is empty

Transmit (I2C mode only)

1 = Transmit in progress, SSPBUF is full

0 = Transmit complete, SSPBUF is empty

Legend:

R = Readable bit

- n = Value at POR

W = Writable bit

’1’ = Bit is set

U = Unimplemented bit, read as ‘0’

’0’ = Bit is cleared

x = Bit is unknown

 2001 Microchip Technology Inc.

Preliminary

DS39544A-page 59

Share Link: