DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

Z80230 查看數據表(PDF) - Zilog

零件编号
产品描述 (功能)
生产厂家
Z80230 Datasheet PDF : 317 Pages
First Prev 201 202 203 204 205 206 207 208 209 210 Next Last
Application Note
The Zilog Datacom Family with the 80186 CPU
SERIAL INTERFACING (Continued)
Table 10. Pin Assignments of Line Driver/Receiver Connectors
J13-J14
J13-J14
J15
J15
Pin # DTE signal
DCE signal
DTE signal
DCE signal
Direction/where used
7
8
/DCD
9
10
GND
11
12
/RxC
13
/TxCO
14
/TxCI
15
16
/RI
/DCD
GND
/RxC
/TxCI
/TxCO
/RI
/DDC
GND
/RxC
/TxCO
/TxCI
/DCD
GND
/RxC
/TxCI
/TxCO
Output to J1B, J2B, J3B
Input from J1A, J2A, J3A, J4
Output to J1B, J2B, J3B
Input from J1A, J2A, J3A
Output to J1-3
Input from J1-3 [3]
Output to J1B, J2B
Input from J1A, J2A
Note:
[3] Various conventions have been used to combine synchronous clock inputs and modem control inputs on Apple Macintosh connectors
similar to J4, as described in a later section.
Comparison of the two preceding charts leads to several
conclusions:
s Pins 1-5 can always be jumpered straight across from a
J5-J10 connector block to a J13-J15 connector block.
s In a synchronous environment, the Transmit clock can
be either driven or received and the Receive clock can
be received from the DTE connector or sent on the DCE
connector.
The 10-pin J11 and J12 jumper blocks provide for
connections to the Port pins of the IUSC and (M)USC,
respectively. As with J5-J10, these connections may be to
the customer’s off-board custom circuits and/or to certain
pins in the J13-J15 blocks. The following pin assignment is
determined so that if a 2-channel USC is plugged into the
(M)USC socket, J12 has the same pin-out for the USC’s B
channel as do J5-J10 for other channels.
Table 11. Pin Assignments of Controller Port Connectors
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
J11: IUSC Signal
PORT1 (Clock 1 In)
PORT4 (Xmit TSA Gate Out)
(N/C)
PORT0 (Clock 0 In)
(N/C)
PORT3 (Rcv TSA Gate Out)
(N/C)
PORT5 (Rcv Sync Out)
PORT2
GND
PORT6 (Rcv Sync In)
PORT7 (Xmit Complete Out)
J12: (M)USC Signal
PORT1
PORT4 (Xmit TSA Gate Out)
(N/C)
PORT0
(N/C)
PORT3 (Rcv TSA Gate Out)
(SYSCLK)
PORT5 (Rcv Sync Out)
PORT2
GND
PORT6 (Rcv Sync In)
PORT7 (Xmit Complete Out)
Finally, an unpopulated 4-pin oscillator socket is included
on the board with its output connected to a single
jumper/wire-wrap pin. This socket can be populated with a
user-supplied oscillator and connected to various clock
pin(s) among J5-J15.
6-70
UM010901-0601

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]