AD9705-DPG2-EBZ(RevD) View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
AD9705-DPG2-EBZ
(Rev.:RevD)
(Rev.:RevD)
Analog Devices
AD9705-DPG2-EBZ Datasheet PDF : 42 Pages
| |||
Data Sheet
AD9704
AD9704/AD9705/AD9706/AD9707
PIN 1
INDICATOR
DB1 1
DB0 (LSB) 2
DVDD 3
NC 4
NC 5
NC 6
NC 7
NC 8
AD9704
TOP VIEW
(Not to Scale)
24 FS ADJ
23 REFIO
22 ACOM
21 IOUTA
20 IOUTB
19 OTCM
18 AVDD
17 PIN/SPI/RESET
NOTES
1. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN.
2. IT IS RECOMMENDED THAT THE EXPOSED PAD BE
THERMALLY CONNECTED TO A COPPER GROUND
PLANE FOR ENHANCED ELECTRICAL AND THERMAL
PERFORMANCE.
Figure 6. AD9704 Pin Configuration
Table 12. AD9704 Pin Function Descriptions
Pin No. Mnemonic Description
28 to 32, 1 DB6 to DB1 Data Bit 6 to Data Bit 1.
2
DB0 (LSB)
Least Significant Data Bit (LSB).
3
DVDD
Digital Supply Voltage (1.7 V to 3.6 V). DVDD, AVDD, and CLKVDD must be at the same supply voltage.
4 to 9
NC
No Connect.
10, 26
DCOM
Digital Common.
11
CLKVDD
Clock Supply Voltage (1.7 V to 3.6 V). DVDD, AVDD, and CLKVDD must be at the same supply voltage.
12
CLK+
Positive Differential Clock Input.
13
CLK−
Negative Differential Clock Input.
14
CLKCOM
Clock Common.
15
CMODE/SCLK In pin mode, this pin selects the clock input type. Connect to CLKCOM for single-ended clock receiver (drive CLK+
and float CLK−). Connect to CLKVDD for differential receiver. In SPI mode, this pin is the serial data clock input.
16
MODE/SDIO In pin mode, this pin selects the input data format. Connect to DCOM for straight binary, and DVDD for twos
complement. In SPI mode, this pin acts as SPI data input/output.
17
PIN/SPI/RESET Selects SPI Mode or Pin Mode Operation. Active high for pin mode operation and active low for SPI mode
operation. Pulse high to reset SPI registers to default values.
18
AVDD
Analog Supply Voltage (1.7 V to 3.6 V). DVDD, AVDD, and CLKVDD must be at the same supply voltage.
19
OTCM
Adjustable Output Common Mode. Refer to the Theory of Operation section for details.
20
IOUTB
Complementary DAC Current Output. Full-scale current is sourced when all data bits are 0s.
21
IOUTA
DAC Current Output. Full-scale current is sourced when all data bits are 1s.
22
ACOM
Analog Common.
23
REFIO
Reference Input/Output. Serves as reference input when internal reference disabled. Serves as 1.0 V reference output
when internal reference is activated. Requires a 0.1 µF capacitor to ACOM when internal reference is activated.
24
FS ADJ
Full-Scale Current Output Adjust.
25
SLEEP/CSB In pin mode, active high powers down chip. In SPI mode, this pin is the serial port chip select (active low).
27
DB7 (MSB) Most Significant Data Bit (MSB).
EPAD
It is recommended that the exposed pad be thermally connected to a copper ground plane for enhanced
electrical and thermal performance.
Rev. D | Page 15 of 42
Share Link: 