ATSAMA5D35A-CU View Datasheet(PDF) - Atmel Corporation

Part Name

Description

Manufacturer

ATSAMA5D35A-CU

SMART ARM-based MPU

Atmel Corporation 

Doc. Rev.

11121C Comments

Change

Request

Ref.

Section 54. “Electrical Characteristics”

Minor editorial and formatting changes throughout

rfo

Table 54-1 “Absolute Maximum Ratings*”:

rfo

- deleted “Operating Temperature (Industrial)..............-40° C to +85°C”

- added (VDDFUSE)...3.3V

Section 54.2 “DC Characteristics”: in first sentence, replaced “TA = -40°C to +85°C” with “TA = -40°C to +105°C” rfo

Table 54-2 “DC Characteristics”:

rfo

- deleted parameters VVDDCORErip / VDDCORE ripple, VVDDBUrip / VDDBU ripple, VVDDPLLArip / VDDPLLA ripple,

and VVDDOSCrip / VDDOSC ripple

- added parameters VVDDFUSE / DC Supply FUSE box and IVDDFUSE / VDDFUSE current

- updated parameter ISC / Static Current

- updated parameter name and conditions of VVDDOSC

Updated Section 54.3 “Power Consumption”

rfo

Table 54-9 “Processor Clock Waveform Parameters”: updated conditions, minimum values and footnote

rfo

Table 54-10 “Master Clock Waveform Parameters”: updated conditions and footnote

rfo

Section 54.5.1 “Crystal Oscillator Characteristics”: in first sentence, replaced “TA = -40°C to +85°C” with “TA = - rfo

40°C to +105°C”

Table 54-15 “32 kHz Oscillator Characteristics”: corrected referenced register name and section in note

rfo

Table 54-19 “PLLA Characteristics”: updated output frequency conditions

9031

Table 54-56 “System Clock Waveform Parameters”: replaced “T = 85°C” with “TA = 85°C” in conditions

rfo

Table 54-57 “System Clock Waveform Parameters”: replaced “T = 85°C” with “TA = 85°C” in conditions

rfo

Table 54-58 “System Clock Waveform Parameters”: replaced “T = 85°C” with “TA = 85°C” in conditions

rfo

Section “”: updated content; removed “MCI Timings” figure and table

rfo

Section 54.21 “Two-wire Interface Characteristics”: updated Table 54-73 “Two-wire Serial Bus Requirements” 8819

and the corresponding notes

Table 54-69 “EMAC MII Specific Signals”: in footnote, corrected link to note 2 of Table 54-68 “EMAC Signals rfo

Relative to EMDC” (was incorrectly linked to note of Table 54-60 “SSC Timings with 3.3V Peripheral Supply”)

Table 54-70 “RMII Mode”: in footnote, corrected link to note 2 of Table 54-68 “EMAC Signals Relative to

rfo

EMDC” (was incorrectly linked to note of Table 54-60 “SSC Timings with 3.3V Peripheral Supply”)

Section 55. “Mechanical Characteristics”

Added Section 55.2 “324-ball TFBGA Mechanical Characteristics” (introduced new package)

9035

Section 56. “SAMA5D3 Ordering Information”

Updated Table 56-1 “SAMA5D3 Ordering Information” (includes adding SAMA5D36 device references and

introduction of 324-ball TFBGA package)

8822

9035

Section 59. “Errata”

Updated Section 59.7 “LCD Controller (LCDC)”

Added Section 60.7 “Watchdog Timer (WDT)”

8971

8969

1904

SAMA5D3 Series [DATASHEET]

Atmel-11121F-ATARM-SAMA5D3-Series-Datasheet_02-Feb-16

Share Link: