AD8361ART-EVAL(2000) View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
AD8361ART-EVAL Datasheet PDF : 16 Pages
| |||
AD8361
Alternatively, a reactive match can be implemented using a shunt
inductor to ground and a series capacitor as shown in Figure
39c. A method for hand calculating the appropriate matching
components is shown on page 12 of the AD8306 data sheet.
Matching in this manner results in very small values for CM,
especially at high frequencies. As a result, a stray capacitance as
small as 1 pF can significantly degrade the quality of the match.
The main advantage of a reactive match is the increase in sensi-
tivity that results from the input voltage being “gained up” (by
the square root of the impedance ratio) by the matching network.
Table III shows recommended values for reactive matching.
Table III. Recommended Values for a Reactive Input Match
(Figure 39c)
Frequency
CM
LM
MHz
pF
nH
100
800
900
1800
1900
2500
16
180
2
15
2
12
1.5
4.7
1.5
4.7
1.5
3.3
Input Coupling Using a Series Resistor
Figure 39d shows a technique for coupling the input signal
into the AD8361, which may be applicable where the input signal
is much larger than the input range of the AD8361. A series
resistor combines with the input impedance of the AD8361 to
attenuate the input signal. Since this series resistor forms a
divider with the frequency-dependent input impedance, the
apparent gain changes greatly with frequency. However, this
method has the advantage of very little power being “tapped
off” in RF power transmission applications. If the resistor is large
compared to the transmission line’s impedance then the VSWR of
the system is relatively unaffected.
250
1.7
200
1.4
150
1.1
100
0.8
50
0.5
0
0.2
0
500 1000 1500 2000 2500 3000 3500
FREQUENCY – MHz
Figure 40. Input Impedance vs. Frequency, Supply 3 V,
SOT-23-6L
Selecting the Filter Capacitor
The AD8361’s internal 27 pF filter capacitor is connected in
parallel with an internal resistance that varies with signal level
from 2 kΩ for small signals to 500 Ω for large signals. The
resulting low-pass corner frequency between 3 MHz and 12 MHz
provides adequate filtering for all frequencies above 240 MHz
(i.e., ten times the frequency at the output of the squarer, which
is twice the input frequency). However, signals with high peak-
to-average ratios, such as CDMA or W-CDMA signals, and
with low frequency components, require additional filtering.
TDMA signals, such as GSM, PDC, or PHS have a peak-to-
average ratio that is close to that of a sinusoid, and the internal
filter is adequate.
The filter capacitance of the AD8361 can be augmented by
connecting a capacitor between Pin 6 (FLTR) and VPOS.
Table IV shows the effect of several capacitor values for various
communications standards with high peak-to-average ratios along
with the residual ripple at the output, in peak-to-peak and rms
volts. Note that large filter capacitors will increase the enable
and pulse response times, as discussed below.
Table IV. Effect of Waveform and CFILT on Residual AC
Waveform
CFILT
IS95 Reverse Link Open
0.01 µF
0.1 µF
IS95 8-Channel
Forward Link
0.01 µF
0.1 µF
W-CDMA 15
Channel
0.01 µF
0.1 µF
Output
V dc
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
Residual AC
mV p-p mV rms
550
100
1000 180
2000 360
40
6
160
20
430
60
20
3
40
6
110
18
290
40
975
150
2600 430
50
7
190
30
670
95
225
35
940
135
2500 390
45
6
165
25
550
80
Operation at Low Frequencies
Although the AD8361 is specified for operation up to 2.5 GHz,
there is no lower limit on the operating frequency. It is only nec-
essary to increase the input coupling capacitor to reduce the
corner frequency of the input high-pass filter (use an input resis-
tance of 225 Ω for frequencies below 100 MHz). It is also
necessary to increase the filter capacitor so that the signal at the
output of the squaring circuit is free of ripple. The corner fre-
quency will be set by the combination of the internal resistance of
2 kΩ and the external filter capacitance.
Power Consumption, Enable and Power-On
The quiescent current consumption of the AD8361 varies with
the size of the input signal from about 1 mA for no signal up to
7 mA at an input level of 0.66 V rms (9.4 dBm re 50 Ω). If the
input is driven beyond this point, the supply current increases
steeply (see Figure 12). There is little variation in quiescent
current with power supply voltage.
–12–
REV. A
Share Link: 