ADE7880ACPZ-RL(RevA) View Datasheet(PDF) - Analog Devices

Part Name

Description

Manufacturer

ADE7880ACPZ-RL
(Rev.:RevA)

Polyphase Multifunction Energy Metering IC with Harmonic Monitoring

Analog Devices 

Data Sheet

ADE7880

256 kHz) for 60 Hz systems. The delays between phase voltages

or phase currents are used to characterize how balanced the

load is. The delays between phase voltages and currents are

used to compute the power factor on each phase as shown in

the following Equation 6:

cosφx

=

cos

⎡

⎢

⎣

ANGLEx

×

360o × f LINE

256 kHz

⎤

⎥

⎦

(6)

where fLINE = 50 Hz or 60 Hz.

in STATUS1 register is set to 1 to indicate the condition and the bit

VSPHASE[0] in the PHSTATUS register is set back to 0.

Bits VSPHASE[1] and VSPHASE[2] relate to the sag events on

Phase B and Phase C in the same way: when Phase B or Phase C

voltage stays below SAGLVL, they are set to 1. When the phase

voltages are above SAGLVL, they are set to 0.

FULL SCALE

SAGLVL[23:0]

PHASE B VOLTAGE

Period Measurement

The ADE7880 provides the period measurement of the line in

the voltage channel. The period of each phase voltage is

measured and stored in three different registers, APERIOD,

BPERIOD, and CPERIOD. The period registers are 16-bit

unsigned registers and update every line period. Because of the

LPF1 filter (see Figure 50), a settling time of 30 ms to 40 ms is

associated with this filter before the measurement is stable.

The period measurement has a resolution of 3.90625 μs/LSB

(256 kHz clock), which represents 0.0195% (50 Hz/256 kHz)

when the line frequency is 50 Hz and 0.0234% (60 Hz/256 kHz)

when the line frequency is 60 Hz. The value of the period registers

for 50 Hz networks is approximately 5120 (256 kHz/50 Hz) and

for 60 Hz networks is approximately 4267 (256 kHz/60 Hz). The

length of the registers enables the measurement of line frequencies

as low as 3.9 Hz (256 kHz/216). The period registers are stable at

±1 LSB when the line is established and the measurement does

not change.

The following equations can be used to compute the line period

and frequency using the period registers:

TL

=

PERIOD[15:0]

256E3

[sec]

(7)

fL

=

256E3

PERIOD[15:0]

[Hz]

(8)

Phase Voltage Sag Detection

The ADE7880 can be programmed to detect when the absolute

value of any phase voltage drops below or grows above a certain

peak value for a number of half-line cycles. The phase where

this event takes place and the state of the phase voltage relative

to the threshold is identified in Bits[14:12] (VSPHASE[x]) of

the PHSTATUS register. An associated interrupt is triggered

when any phase drops below or grows above a threshold. This

condition is illustrated in Figure 56.

Figure 56 shows Phase A voltage falling below a threshold that

is set in the SAG level register (SAGLVL) for four half-line cycles

(SAGCYC = 4). When Bit 16 (SAG) in the STATUS1 register is set

to 1 to indicate the condition, Bit VSPHASE[0] in the PHSTATUS

register is also set to 1 because the phase A voltage is below

SAGLVL. The microcontroller then writes back STATUS1 register

with Bit 16 (SAG) set to 1 to erase the bit and bring IRQ1 interrupt

pin back high. Then the phase A voltage stays above the SAGLVL

threshold for four half-line cycles (SAGCYC = 4). The Bit 16 (SAG)

SAGCYC[7:0] = 0x4

PHASE A VOLTAGE

SAGCYC[7:0] = 0x4

BIT 16 (SAG) IN

STATUS1[31:0]

IRQ1 PIN

VSPHASE[0] =

PHSTATUS[12]

VSPHASE[1] =

PHSTATUS[13]

STATUS1[16] CANCELLED BY

A WRITE TO STATUS1[31:0]

WITH SAG BIT SET

STATUS[16] SET TO 1

IRQ1 PIN GOES HIGH

BECAUSE STATUS1[16]

CANCELLED BY A WRITE

TO STATUS[31:0] WITH SAG

BIT SET

PHSTATUS[12] SET TO 1

BECAUSE PHASE A

VOLTAGE WAS BELOW

SAGLVL FOR SAGCYC

HALF LINE CYCLES

PHSTATUS[12] CLEARED

TO 0 BECAUSE PHASE A

VOLTAGE WAS ABOVE

SAGLVL FOR SAGCYC

HALF LINE CYCLES

PHSTATUS[13] SET TO 1

Figure 56. SAG Detection

The SAGCYC register represents the number of half-line cycles

the phase voltage must remain below or above the level indicated

in the SAGLVL register to trigger a SAG interrupt ; 0 is not a

valid number for SAGCYC. For example, when the SAG cycle

(SAGCYC[7:0]) contains 0x07, the SAG flag in the STATUS1

register is set at the end of the seventh half line cycle for which

the line voltage falls below the threshold. If Bit 16 (SAG) in

MASK1 is set, the IRQ1 interrupt pin is driven low in case of a

SAG event in the same moment the Status Bit 16 (SAG) in

STATUS1 register is set to 1. The SAG status bit in the STATUS1

register and the IRQ1 pin is returned to high by writing to the

STATUS1 register with the status bit set to 1.

When the Phase B voltage falls below the indicated threshold

into the SAGLVL register for two line cycles, Bit VSPHASE[1]

in the PHSTATUS register is set to 1 (see Figure 56). Simultane-

ously, Bit 16 (SAG) in the STATUS1 register is set to 1 to indicate

the condition.

Note that the internal zero-crossing counter is always active. By

setting the SAGLVL register, the first SAG detection result is,

therefore, not executed across a full SAGCYC period. Writing to

the SAGCYC register when the SAGLVL register is already initia-

lized resets the zero-crossing counter, thus ensuring that the first

SAG detection result is obtained across a full SAGCYC period.

Rev. A | Page 33 of 104

Share Link: