ADE7880ACPZ-RL(RevA) View Datasheet(PDF) - Analog Devices

Part Name

Description

Manufacturer

ADE7880ACPZ-RL
(Rev.:RevA)

Polyphase Multifunction Energy Metering IC with Harmonic Monitoring

Analog Devices 

Data Sheet

register is set to 1. To find the phase that triggered the interrupt,

one of either the IPEAK or VPEAK registers is read immediately

after reading the STATUS1 register. Next, the status bits are

cleared, and the IRQ1 pin is set to high by writing to the

STATUS1 register with the status bit set to 1.

Note that the internal zero-crossing counter is always active. By

setting Bits[4:2] (PEAKSEL[2:0]) in the MMODE register, the

first peak detection result is, therefore, not executed across a full

PEAKCYC period. Writing to the PEAKCYC register when the

PEAKSEL[2:0] bits are set resets the zero-crossing counter,

thereby ensuring that the first peak detection result is obtained

across a full PEAKCYC period.

Overvoltage and Overcurrent Detection

The ADE7880 detects when the instantaneous absolute value

measured on the voltage and current channels becomes greater

than the thresholds set in the OVLVL and OILVL 24-bit

unsigned registers. If Bit 18 (OV) in the MASK1 register is set,

the IRQ1 interrupt pin is driven low in case of an overvoltage

event. There are two status flags set when the IRQ1 interrupt

pin is driven low: Bit 18 (OV) in the STATUS1 register and one

of Bits[11:9] (OVPHASE[2:0]) in the PHSTATUS register to

identify the phase that generated the overvoltage. The Status

Bit 18 (OV) in the STATUS1 register and all Bits[11:9]

(OVPHASE[2:0]) in the PHSTATUS register are cleared, and

the IRQ1 pin is set to high by writing to the STATUS1 register

with the status bit set to 1. Figure 60 presents overvoltage

detection in the Phase A voltage.

PHASE A

VOLTAGE CHANNEL

OVERVOLTAGE

DETECTED

OVLVL[23:0]

BIT 18 (OV) OF

STATUS1

BIT 9 (OVPHASE)

OF PHSTATUS

STATUS1[18] AND

PHSTATUS[9]

CANCELLED BY A

WRITE OF STATUS1

WITH OV BIT SET.

Figure 60. Overvoltage Detection

ADE7880

Whenever the absolute instantaneous value of the voltage goes

above the threshold from the OVLVL register, Bit 18 (OV) in

the STATUS1 register and Bit 9 (OVPHASE[0]) in the PHSTATUS

register are set to 1. Bit 18 (OV) of the STATUS1 register and

Bit 9 (OVPHASE[0]) in the PHSTATUS register are cancelled

when the STATUS1 register is written with Bit 18 (OV) set to 1.

The recommended procedure to manage overvoltage events is

the following:

1. Enable OV interrupts in the MASK1 register by setting

Bit 18 (OV) to 1.

2. When an overvoltage event happens, the IRQ1 interrupt

pin goes low.

3. The STATUS1 register is read with Bit 18 (OV) set to 1.

4. The PHSTATUS register is read, identifying on which

phase or phases an overvoltage event happened.

5. The STATUS1 register is written with Bit 18 (OV) set to 1.

In this moment, Bit OV is erased and also all Bits[11:9]

(OVPHASE[2:0]) of the PHSTATUS register.

In case of an overcurrent event, if Bit 17 (OI) in the MASK1

register is set, the IRQ1 interrupt pin is driven low. Immediately,

Bit 17 (OI) in the STATUS1 register and one of Bits[5:3]

(OIPHASE[2:0]) in the PHSTATUS register, which identify

the phase that generated the interrupt, are set. To find the

phase that triggered the interrupt, the PHSTATUS register

is read immediately after reading the STATUS1 register. Next,

Status Bit 17 (OI) in the STATUS1 register and Bits[5:3]

(OIPHASE[2:0]) in the PHSTATUS register are cleared and the

IRQ1 pin is set to high by writing to the STATUS1 register with

the status bit set to 1. The process is similar with overvoltage

detection.

Overvoltage and Overcurrent Level Set

The content of the overvoltage (OVLVL), and overcurrent,

(OILVL) 24-bit unsigned registers is compared to the absolute

value of the voltage and current channels. The maximum value of

these registers is the maximum value of the HPF outputs:

+5,326,737 (0x514791). When the OVLVL or OILVL register is

equal to this value, the overvoltage or overcurrent conditions

are never detected. Writing 0x0 to these registers signifies the

overvoltage or overcurrent conditions are continuously

detected, and the corresponding interrupts are permanently

triggered.

As stated in the Current Waveform Gain Registers section, the

serial ports of the ADE7880 work on 32-, 16-, or 8-bit words.

Similar to the register presented in Figure 57, OILVL and

OVLVL registers are accessed as 32-bit registers with the eight

MSBs padded with 0s.

Rev. A | Page 35 of 104

Share Link: