PIC10F220IP(2006) View Datasheet(PDF) - Microchip Technology
Part Name
Description
Manufacturer
PIC10F220IP Datasheet PDF : 78 Pages
| |||
PIC10F220/222
TABLE 5-3: SUMMARY OF PORT REGISTERS
Address Name
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3
Bit 2 Bit 1 Bit 0
Value on
Power-On
Reset
Value on
All Other Resets
N/A
N/A
03h
06h
Legend:
Note 1:
TRISGPIO
—
—
—
— I/O Control Registers
---- 1111
---- 1111
OPTION
STATUS
GPWU GPPU T0CS T0SE PSA PS2 PS1 PS0 1111 1111
GPWUF —
—
TO PD
Z
DC C 0001 1xxx
1111 1111
q00q quuu(1)
GPIO
—
—
—
— GP3 GP2 GP1 GP0 ---- xxxx
---- uuuu
Shaded cells not used by Port registers, read as ‘0’, – = unimplemented, read as ‘0’, x = unknown, u = unchanged,
q = depends on condition.
If Reset was due to wake-up on pin change, then bit 7 = 1. All other Resets will cause bit 7 = 0.
5.4 I/O Programming Considerations
5.4.1 BIDIRECTIONAL I/O PORTS
Some instructions operate internally as read followed
by write operations. The BCF and BSF instructions, for
example, read the entire port into the CPU, execute the
bit operation and re-write the result. Caution must be
used when these instructions are applied to a port
where one or more pins are used as input/outputs. For
example, a BSF operation on bit 2 of GPIO will cause
all eight bits of GPIO to be read into the CPU, bit 2 to
be set and the GPIO value to be written to the output
latches. If another bit of GPIO is used as a bidirectional
I/O pin (say bit 0) and it is defined as an input at this
time, the input signal present on the pin itself would be
read into the CPU and rewritten to the data latch of this
particular pin, overwriting the previous content. As long
as the pin stays in the Input mode, no problem occurs.
However, if bit 0 is switched into Output mode later on,
the content of the data latch may now be unknown.
Example 5-1 shows the effect of two sequential
Read-Modify-Write instructions (e.g., BCF, BSF, etc.)
on an I/O port.
A pin actively outputting a high or a low should not be
driven from external devices at the same time in order
to change the level on this pin (“wired-or”, “wired-and”).
The resulting high output currents may damage the
chip.
EXAMPLE 5-1:
I/O PORT READ-MODIFY-
WRITE INSTRUCTIONS
;Initial GPIO Settings
;GPIO<3:2> Inputs
;GPIO<1:0> Outputs
;
;
GPIO latch GPIO pins
;
---------- ----------
BCF GPIO, 1 ;---- pp01 ---- pp11
BCF GPIO, 0 ;---- pp10 ---- pp11
MOVLW 007h;
TRIS GPIO
;---- pp10 ---- pp11
;
Note: The user may have expected the pin values to
be ---- pp00. The second BCF caused GP1
to be latched as the pin value (High).
5.4.2
SUCCESSIVE OPERATIONS ON I/O
PORTS
The actual write to an I/O port happens at the end of an
instruction cycle, whereas for reading, the data must be
valid at the beginning of the instruction cycle (Figure 5-5).
Therefore, care must be exercised if a write followed by
a read operation is carried out on the same I/O port. The
sequence of instructions should allow the pin voltage to
stabilize (load dependent) before the next instruction
causes that file to be read into the CPU. Otherwise, the
previous state of that pin may be read into the CPU rather
than the new state. When in doubt, it is better to separate
these instructions with a NOP or another instruction not
accessing this I/O port.
FIGURE 5-5:
SUCCESSIVE I/O OPERATION
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
PC
Instruction
Fetched MOVWF GPIO
PC + 1
MOVF GPIO, W
PC + 2
NOP
PC + 3
NOP
GP<2:0>
Instruction
Executed
Port pin
written here
Port pin
sampled here
MOVWF GPIO MOVF GPIO,W
NOP
(Write to GPIO) (Read GPIO)
This example shows a write to GPIO followed
by a read from GPIO.
Data setup time = (0.25 TCY – TPD)
where: TCY = instruction cycle
TPD = propagation delay
Therefore, at higher clock frequencies, a
write followed by a read may be problematic.
© 2006 Microchip Technology Inc.
Preliminary
DS41270B-page 23
Share Link: 