PIC16LF88/SS View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC16LF88/SS

18/20/28-Pin Enhanced Flash MCUs with nanoWatt Technology

Microchip Technology 

PIC16F87/88

18.4 DC Characteristics: PIC16F87/88 (Industrial, Extended)

PIC16LF87/88 (Industrial)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C  TA  +85°C for industrial

-40°C  TA  +125°C for extended

Operating voltage VDD range as described in DC Specification,

Section 18.1 “DC Characteristics: Supply Voltage”.

Param

No.

Sym

Characteristic

Min

Typ† Max Units

Conditions

VIL Input Low Voltage

I/O ports:

D030

with TTL buffer

VSS

— 0.15 VDD V For entire VDD range

D030A

VSS

— 0.8V V 4.5V  VDD  5.5V

D031

with Schmitt Trigger buffer

VSS

— 0.2 VDD V

D032

MCLR, OSC1 (in RC mode)

VSS

— 0.2 VDD V (Note 1)

D033

OSC1 (in XT and LP mode)

VSS

— 0.3V V

OSC1 (in HS mode)

VSS

— 0.3 VDD V

Ports RB1 and RB4:

D034

with Schmitt Trigger buffer

VSS

— 0.3 VDD V For entire VDD range

VIH Input High Voltage

I/O ports:

D040

with TTL buffer

2.0

— VDD

V 4.5V  VDD  5.5V

D040A

0.25 VDD + 0.8V — VDD

V For entire VDD range

D041

with Schmitt Trigger buffer

0.8 VDD

— VDD

V For entire VDD range

D042

MCLR

0.8 VDD

— VDD

V

D042A

OSC1 (in XT and LP mode)

1.6V

— VDD

V

OSC1 (in HS mode)

0.7 VDD

— VDD

V

D043

OSC1 (in RC mode)

0.9 VDD

— VDD

V (Note 1)

Ports RB1 and RB4:

D044

with Schmitt Trigger buffer

D070 IPURB PORTB Weak Pull-up Current

0.7 VDD

50

— VDD

250 400

V For entire VDD range

A VDD = 5V, VPIN = VSS

IIL Input Leakage Current (Notes 2, 3)

D060

I/O ports

—

—

±1

A Vss  VPIN  VDD, pin at

high-impedance

D061

D063

MCLR

OSC1

—

—

±5

A Vss  VPIN  VDD

—

—

±5

A Vss  VPIN  VDD, XT, HS

and LP oscillator

configuration

*

†

Note 1:

2:

3:

These parameters are characterized but not tested.

Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the

PIC16F87/88 be driven with external clock in RC mode.

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

Negative current is defined as current sourced by the pin.

 2002-2013 Microchip Technology Inc.

DS30487D-page 173

Share Link: