PIC16LF88/SS View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC16LF88/SS

18/20/28-Pin Enhanced Flash MCUs with nanoWatt Technology

Microchip Technology 

PIC16F87/88

18.4 DC Characteristics: PIC16F87/88 (Industrial, Extended)

PIC16LF87/88 (Industrial) (Continued)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C  TA  +85°C for industrial

-40°C  TA  +125°C for extended

Operating voltage VDD range as described in DC Specification,

Section 18.1 “DC Characteristics: Supply Voltage”.

Param

No.

Sym

Characteristic

Min

Typ† Max Units

Conditions

VOL Output Low Voltage

D080

I/O ports

—

— 0.6

V IOL = 8.5 mA, VDD = 4.5V,

-40C to +125C

D083

OSC2/CLKO

(RC oscillator configuration)

—

— 0.6

V IOL = 1.6 mA, VDD = 4.5V,

-40C to +125C

VOH Output High Voltage

D090

I/O ports (Note 3)

VDD – 0.7

—

—

V IOH = -3.0 mA, VDD = 4.5V,

-40C to +125C

D092

OSC2/CLKO

(RC oscillator configuration)

VDD – 0.7

—

—

V IOH = -1.3 mA, VDD = 4.5V,

-40C to +125C

Capacitive Loading Specs on Output Pins

D100 COSC2 OSC2 pin

—

—

15

pF In XT, HS and LP modes

when external clock is used

to drive OSC1

D101 CIO All I/O pins and OSC2

(in RC mode)

—

—

50

pF

D102 CB SCL, SDA in I2C™ mode

—

— 400 pF

Data EEPROM Memory

D120 ED Endurance

100K

10K

1M —

100K —

E/W -40C to 85C

E/W +85C to +125C

D121 VDRW VDD for Read/Write

VMIN

— 5.5

V Using EECON to read/write,

VMIN = min. operating voltage

D122 TDEW Erase/Write Cycle Time

—

4

8

ms

Program Flash Memory

D130 EP Endurance

10K

100K — E/W -40C to 85C

1K

10K — E/W +85C to +125C

D131 VPR VDD for Read

VMIN

— 5.5

V

D132A

VDD for Erase/Write

VMIN

— 5.5

V Using EECON to read/write,

VMIN = min. operating voltage

D133 TPE Erase Cycle Time

—

2

4

ms

D134 TPW Write Cycle Time

—

2

4

ms

* These parameters are characterized but not tested.

† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

Note 1: In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the

PIC16F87/88 be driven with external clock in RC mode.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

3: Negative current is defined as current sourced by the pin.

DS30487D-page 174

 2002-2013 Microchip Technology Inc.

Share Link: