PIC16C711-04I/SP View Datasheet(PDF) - Microchip Technology
Part Name
Description
Manufacturer
PIC16C711-04I/SP Datasheet PDF : 176 Pages
| |||
PIC16C71X
Applicable Devices 710 71 711 715
11.3 DC Characteristics:
DC CHARACTERISTICS
PIC16C710-04 (Commercial, Industrial, Extended)
PIC16C711-04 (Commercial, Industrial, Extended)
PIC16C710-10 (Commercial, Industrial, Extended)
PIC16C711-10 (Commercial, Industrial, Extended)
PIC16C710-20 (Commercial, Industrial, Extended)
PIC16C711-20 (Commercial, Industrial, Extended)
PIC16LC710-04 (Commercial, Industrial, Extended)
PIC16LC711-04 (Commercial, Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature 0˚C ≤ TA ≤ +70˚C (commercial)
-40˚C ≤ TA ≤ +85˚C (industrial)
-40˚C ≤ TA ≤ +125˚C (extended)
Operating voltage VDD range as described in DC spec Section 11.1 and
Section 11.2.
Param
No.
Characteristic
Sym Min Typ Max Units
†
Conditions
Input Low Voltage
I/O ports
VIL
D030
D030A
D031
with TTL buffer
with Schmitt Trigger buffer
VSS - 0.15VDD V For entire VDD range
VSS - 0.8V V 4.5 ≤ VDD ≤ 5.5V
VSS - 0.2VDD V
D032
MCLR, OSC1
(in RC mode)
VSS - 0.2VDD V
D033
OSC1 (in XT, HS and LP)
Input High Voltage
VSS - 0.3VDD V Note1
D040
D040A
I/O ports
with TTL buffer
VIH
-
2.0 - VDD
0.25VDD - VDD
+ 0.8V
V 4.5 ≤ VDD ≤ 5.5V
V For entire VDD range
D041
D042
with Schmitt Trigger buffer
MCLR, RB0/INT
0.8VDD - VDD
0.8VDD - VDD
V For entire VDD range
V
D042A OSC1 (XT, HS and LP)
0.7VDD - VDD V Note1
D043
D070
OSC1 (in RC mode)
PORTB weak pull-up current
0.9VDD - VDD
IPURB 50 250 400
V
µA VDD = 5V, VPIN = VSS
D060
D061
D063
Input Leakage Current (Notes 2, 3)
I/O ports
IIL
MCLR, RA4/T0CKI
OSC1
-
- ±1 µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
-
-
±5
µA Vss ≤ VPIN ≤ VDD
-
- ±5 µA Vss ≤ VPIN ≤ VDD, XT, HS and LP
osc configuration
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C7X be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
DS30272A-page 92
© 1997 Microchip Technology Inc.
Share Link: 